Panasonic KX-TDE600 Programming Manual Download Page 34

Page: 34 / 60

Value Range

Disable, Enable

FAX Sending Method

Specifies the method of transporting the fax signal.

Default

G.711 Inband

Value Range

G.711 Inband, T.38

Maximum Bit Rate

Specifies the maximum bit rate of the fax signal.

Default

No Speed Limit

Value Range

No Speed Limit, 2400 bps, 4800 bps, 7200 bps, 9600 bps, 12000 bps, 14400 bps

FAX Detection Ability

Enables the use of the FAX Detection Ability feature. This feature enables end-to-end fax signal relay when
the other party prefers a CODEC other than G.711. This feature functions only if the other party supports G.
711.

Default

Enable

Value Range

Disable, Enable

DTMF

Specifies the method to transport DTMF tones.

Default

Outband (RFC2833)

Value Range

Inband, Outband (RFC2833)

Payload Type

Specifies the payload type of RFC2833 for DTMF tones.

Note

Manual programming is required if

DTMF

is set to

Outband (RFC2833)

Programming Manual for Virtual SIP CO Line Card

Document Version 2008-11

3.1.8 Voice/FAX

Summary of Contents for KX-TDE600





























































Search results

Summary of Contents for KX-TDE600

Reviews:

Related manuals for KX-TDE600

Brands by name

Popular brands

Panasonic KX-TDE600, Programming Manual

Search results

Summary of Contents for KX-TDE600

Reviews:

Related manuals for KX-TDE600

Brands by name

Popular brands