Panasonic KX-TC1871CB Page 37 Operating Instructions Manual Download

Page: 37 / 96

Cordless Telephone

To check the number of new calls

When new calls have been received, the

(CALL–DISPLAY)

button flashes

slowly on the base unit.

Ex. You have received 10 new calls.

(›)

(‹)

While the handset is off the base unit:

Press

(›)

(‹)

to turn the display on.

10 new callers

=Directory

10 new callers

≥

Caller information cannot be displayed in the following cases:

≥

—If the caller dialed from an area which does not provide a Call Display service,

the display will show “

Unavailable Name & No.

”.

≥

—If a long distance call is identified, and the caller’s name and/or number cannot

be received, the display will show “

Long distance

”.

≥

—If the caller has requested not to display his/her information, the display will

show “

Private caller

”.

≥

If your unit is connected to a PBX which does not support Call Display services,
you cannot access those services.

≥

The name display service may not be available in some areas. For further
information, please contact your telephone company.

SUN 12:00AM

10 new callers

0 message

While the handset is on the base unit:

Base unit display

Handset display

(CALL–DISPLAY)

Summary of Contents for KX-TC1871CB

































































































Search results

Summary of Contents for KX-TC1871CB

Reviews:

Related manuals for KX-TC1871CB

Brands by name

Popular brands

Panasonic KX-TC1871CB, Operating Instructions Manual

Search results

Summary of Contents for KX-TC1871CB

Reviews:

Related manuals for KX-TC1871CB

Brands by name

Popular brands