manualshive.com logo in svg

Panasonic KX-TC1871CB, Operating Instructions Manual, Page: 92 / 96

Share
Download
Panasonic KX-TC1871CB Operating Instructions Manual Download Page 92

“

Before Requesting Help

92

Problem

You cannot program items,
such as the dialing mode.

Previously programmed
information is erased.

“

Recharge battery

” is

displayed, “

” flashes or

the unit beeps intermittently.

You charged the battery
fully, but “

Recharge

battery

” is still displayed

and/or “

” continues to

flash.

The IN USE/CHARGE
indicator light does not go
out while charging.

Cause and Remedy

≥

Programming is not possible while the
unit is in the talk or speakerphone
mode, when viewing the Caller
List/directory list, or while the answering
system is in use.

≥

Do not pause for over 60 seconds while
programming.

≥

Move closer to the base unit.

≥

(›)

, 

(‹)

, 

BACK

(fi)

or 

FWD/EDIT

(fl)

may have been pressed when you
picked up the handset. Press

(FUNCTION/EXIT/CH)

and try again.

≥

If a power failure occurs, programmed
information may be erased. Reprogram
if necessary.

≥

Charge the battery fully (p. 15).

≥

Clean the charge contacts and charge
again (p. 16).

≥

Install a new battery (p. 87).

≥

This is normal.

Summary of Contents for KX-TC1871CB

































































































Reviews:

No comments