manualshive.com logo in svg

Panasonic KX-TC1871CB, Operating Instructions Manual, Page: 91 / 96

Share
Download
Panasonic KX-TC1871CB Operating Instructions Manual Download Page 91

91

Useful Information

“

Problem

While recording a greeting
message, the unit starts to
ring and stops recording.

During playback, the unit
starts to ring and stops
playback.

The unit does not alert your
pager.

Cause and Remedy

≥

To answer the call, press

(DIGITAL\SP-PHONE)

, or lift the handset

off the base unit or press 

(TALK)

. Start

again from the beginning after hanging
up.

≥

To answer the call, press

(DIGITAL\SP-PHONE)

, or lift the handset

off the base unit or press 

(TALK)

. To

resume playback, press

(NEW\MESSAGE)

after hanging up.

≥

The line mode selection is incorrect. 
See page 19.

General

Problem

The unit does not work.

Cause and Remedy

≥

Check the settings (p. 14–19).

≥

Charge the battery fully (p. 15).

≥

Clean the charge contacts and charge
again (p. 16).

≥

Install the battery properly (p. 15, 87).

≥

Place the handset on the base unit and
unplug the AC adaptor to reset. Plug in,
and try again.

Summary of Contents for KX-TC1871CB

































































































Reviews:

No comments