Panasonic KX-FPG391C, Operating Instructions Manual

Page: 77 / 122

8. Programmable Features
75
8.2 Basic features
Code #00: Setting the Quick Setup
QUICK SETUP
PRESS SET
See page 23 for details.
Code #01: Setting the date and time
SET DATE & TIME
PRESS SET
See page 31 for details.
Code #02: Setting your logo
YOUR LOGO
PRESS SET
See page 32 for details.
Code #03: Setting your fax number
YOUR FAX NO.
PRESS SET
See page 34 for details.
Code #04: Printing a sending report
SENDING REPORT
=ERROR [
±
]
To print a sending report for fax transmission
results (page 54).
“
ERROR
” (default): A sending report will be
printed only when fax transmission fails.
“
ON
” : A sending report will be printed after every
transmission.
“
OFF
” : Sending reports will not be printed.
Code #06: Changing the ring setting in FAX
ONLY mode
FAX RING COUNT
RINGS=3 [
±
]
To change the number of rings before the unit
answers a call in FAX ONLY mode.
You can select
“
1
” , “
2
” , “
3
” (default) or “
4
” .
Code #06: Changing the ring setting in
TAM/FAX mode
TAM RING COUNT
RINGS=3 [
±
]
To change the number of rings before the unit
answers a call in TAM/FAX mode. You can select
“
2
” , “
3
” (default), “
4
” , “
5
” , “
6
” , “
7
” or “
TOLL
SAVER
” . See page 59 for details.
Note:
L
You can also program this feature with the
handset (page 84).
Code #10: Changing the maximum recording
time for incoming messages
RECORDING TIME
=3 MIN [
±
]
“
1 MIN
” , “
2 MIN
” or “
3 MIN
” (default): 1
minute to 3 minutes.
“
GREETING ONLY
” : Only plays your greeting
message.
Note:
L
If you select “
GREETING ONLY
” , the unit will
answer a call with the greeting message, and
then hang up. The unit will not record any
incoming messages.
L
You can also program this feature with the
handset (page 85).
Code #11: Setting the remote operation ID
REMOTE TAM ID
ID=11
1. Press
{
MENU
}
.
2. Press
{#}
, then
{
1
}{
1
}
.
3. Enter a 2-digit number (00–99).
L
The default ID is “
11
” .
4. Press
{
SET
}
.
5. Press
{
MENU
}
.
Note:
L
You can also program this feature with the
handset (page 85).
Code #13: Setting the dialing mode
DIALING MODE
=TONE [
±
]
If you cannot make calls, change this setting
depending on your telephone line service.
“
TONE
” (default): For tone dial service.
“
PULSE
” : For rotary pulse dial service.
Note:
L
You can also program this feature with the
handset (page 86).
Code #17: Setting the ringer tone for outside
calls
RINGER TONE
=TONE 1 [
±
]
To set the base unit ringer tone from one of 7
patterns for outside calls. You can select
“
TONE
1
” (default), “
TONE 2
” , “
TONE 3
” , “
MELODY
1
” , “
MELODY 2
” , “
MELODY 3
” or “
MELODY 4
” .
FPG391C-PFQX2077ZA-en.book Page 75 Tuesday, August 31, 2004 10:12 AM