manualshive.com logo in svg

Panasonic KX-FPC135, Service Manual

The Panasonic KX-FPC135, an excellent all-in-one fax and phone machine, comes with a comprehensive Operating Instructions Manual to assist users in getting the most out of their device. Easily accessible on our website, this manual is available for free download, granting users the convenience of accessing it whenever needed.

Share
Download
background image

7.8.5. LINE AMPLIFIER AND SIDE TONE CIRCUITS

 1. Circuit Operation

The reception signal output from the line transformer T101 is input to pin (6) of IC101 via C126 and R131, and then the signal
is amplified at pin (7) of IC101 and sent to the reception system at 12dB (KX-FPC135), 10dB (KX-FPC141).

The transmission signal goes through C131 and R137 and enters IC101-pin (2), where the signal is amplified to about 18dB
(KX-FPC135), 16.5dB (KX-FPC141). Then, it is output from pin (1) of IC101 and transmitted to T101 via C133 and R125. If the
side tone circuit is not applied, the transmission signal will return to the reception amplifier via C126 and R131. When the side
tone circuit is active, the signal output from IC101 pin (1) passes through C133, R128, R129, C124, C123 and R127 and goes
into the amplifier IC101 pin (5). This circuit is used to cancel the transmission return signal.

7.8.6.  AUTO DISCONNECT CIRCUIT (KX-FPC141 only)

 1. Function

This circuit is used to detect that the telephone connected in parallel to the same line is OFF-HOOK while the unit picks up the
line.

 2. Circuit Operation

If the line is picked up, C104 is charged by the following path shown below.

Tip (Ring)

→

D101

→

R103

→

D102

→

R105

→

Q102

→

PC102

If a telephone connected in parallel goes into OFF-HOOK status, the base of Q102 becomes low and PC102 turns OFF.

When the line is connected, Q102 and PC102 turn on, then pin (153) of IC501 (ASIC) on the digital board becomes low. On
the other hand, When the line is disconnected, Q102 and PC102 turn off, then the pin (153) of IC501 (ASIC) becomes high.

7.8.7. CPC (Calling Party Control) DETECTION CIRCUIT (KX-FPC141 only)

 1. Function

This circuit detects the signal (cuts the current ) output from the converter when the other party finishes ICM recording and goes
into the ON-HOOK status.

TAD detects this signal and disconnects the line. When the TAD is operating, pin (4) of PC104 becomes a low level.

While detecting the CPC signal, pin (4) of PC104 becomes a high level. When the CPC signal is detected, the TAD operation
stops and the line is disconnected.

190

KX-FPC135 / KX-FPC141

Summary of Contents for KX-FPC135









































































































































































































































































Reviews:

No comments

Related manuals for KX-FPC135

Kärcher B 60 W Bp Manual preview
B 60 W Bp
Brand: Kärcher Pages: 312
Siruba Sew Reach ABF Series Instruction Book / Parts List preview
Sew Reach ABF Series
Brand: Siruba Pages: 74
U-Line H-4703 Manual preview
H-4703
Brand: U-Line Pages: 12
Radio Shack 900MHz Owner'S Manual preview
900MHz
Brand: Radio Shack Pages: 32
Viper 50000572 Instructions For Use Manual preview
50000572
Brand: Viper Pages: 93
U.S. Products Agitator 20 Information & Operating Instructions preview
Agitator 20
Brand: U.S. Products Pages: 10
Singer Stylist 533 Manual preview
Stylist 533
Brand: Singer Pages: 68
FONESTAR FOG-9LED Instruction Manual preview
FOG-9LED
Brand: FONESTAR Pages: 16
Horizon Fitness BQ-150 Manual preview
BQ-150
Brand: Horizon Fitness Pages: 45
National 500 PANTHER Instruction Manual preview
500 PANTHER
Brand: National Pages: 27
IDROBASE PerfectCool Cielo Use And Maintenance Manual preview
PerfectCool Cielo
Brand: IDROBASE Pages: 16
JBI PUNCH-BIND Operating Manual preview
PUNCH-BIND
Brand: JBI Pages: 36
Fellowes Galaxy e Wire Instructions Manual preview
Galaxy e Wire
Brand: Fellowes Pages: 94
Brother BB370 Quick Setup Manual preview
BB370
Brand: Brother Pages: 2
Brother CS9100 Operation Manual preview
CS9100
Brand: Brother Pages: 80
Brother CS-8150 Operation Manual preview
CS-8150
Brand: Brother Pages: 141
Brother CV3550 Operation Manual preview
CV3550
Brand: Brother Pages: 37
Brother BAS-750 Parts Book preview
BAS-750
Brand: Brother Pages: 113

Brands by name

Popular brands

Load more brands