manualshive.com logo in svg

Panasonic KX-FPC135, Service Manual

The Panasonic KX-FPC135, an excellent all-in-one fax and phone machine, comes with a comprehensive Operating Instructions Manual to assist users in getting the most out of their device. Easily accessible on our website, this manual is available for free download, granting users the convenience of accessing it whenever needed.

Share
Download
background image

(25) NUMBER OF RECORDING MESSAGE

The number of messages recorded in TAM.

(26) NUMBER OF PC SCAN

The number of times multifunction was used for the Scanner. (The number of pages scanned. If the unit does not have a PC
interface, NONE will be printed.)

(27) NUMBER OF PC-PRINT

The number of times multifunction was used for the Printer. (The number of pages printed. If the unit does not have a PC interface,
NONE will be printed.)

(28) NUMBER OF RECEIVING TO PC

The number of times received in the PC through the FAX serial interface (RS232C). (The number of pages received. If the unit does
not have a PC interface, NONE will be printed.)

(29) NUMBER OF SENDING FROM PC

The number of times transmitted from the PC through the FAX serial interface (RS232C). (The number of pages transmitted. If the
unit does not have a PC interface, NONE will be printed.)

(30) NUMBER OF PRINTING WARNING LIST

The number of warning lists printed until now.

(31) NUMBER OF PRINTING HELP

The number of help lists printed until now.

(32) NUMBER OF DIVIDED PRINTING IN FAX RECEPTION

The number of faxes received that were divided into more than one sheet since the unit was purchased.

(33) DETECTION OF RS232C

When the fax and PC serial cable (RS232C) are connected and the signal is received correctly, COMPLETE will be printed. For
models without a PC interface or when there is a PC interface but the signal cannot be received between the fax and PC,
INCOMPLETE will be printed. (The number of pages transmitted. If the unit does not have a PC interface, NONE will be printed.)

(34) NO. OF IQ-FAX LOADING -OK:

(35) NO. OF IQ-FAX LOADING -NG:

You may not be able to use IQ-FAX if the special subscriber information is not loaded from the IQ-FAX center before use.
Depending on the conditions of the communication line, it may not be completed in one time, so RETRIED will be performed. The
number of OK and NG IQ-FAX loadings will be printed.

(36) FAX MODE

Means the unit received a fax message in the FAX mode.

(37) MAN RCV

Means the unit received a fax message by manual operation.

(38) FRN RCV

Means the unit received a fax message by friendly signal detection.

(39) VOX

Means the unit detected silence or no voice.

(40) RMT DTMF

Means the unit detected DTMF (Remote Fax activation code) entered remotely.

(41) PAL DTMF

Means the unit detected DTMF (Remote Fax activation code) entered by a parallel connected telephone.

(42) TURN-ON

Means the unit started to receive after 15 rings. (Remote Turn On: Service Code #573)

(43) TIME OUT

Means the unit started to receive after Ring Time Out in the EXT-TAM or TEL/FAX mode.

(44) IDENT

Means the unit detected Ring Detection.

(45) CNG OGM

Means the unit detected the CNG while it was sending the Dummy Ring Back Tone in the TEL/FAX mode, or while answering a
call in the EXT-TAM mode. Or means the unit detected the CNG while it was sending the OGM in the ANS/FAX mode.

(46) CNG ICM

Means the unit detected the CNG while it was recording the ICM in the ANS/FAX mode.

109

KX-FPC135 / KX-FPC141

Summary of Contents for KX-FPC135









































































































































































































































































Reviews:

No comments

Related manuals for KX-FPC135

Panasonic KX-TG1855AL Operating Instructions Manual preview
KX-TG1855AL
Brand: Panasonic Pages: 44
Panasonic KX-TCD320E Quick Manual preview
KX-TCD320E
Brand: Panasonic Pages: 6
Panasonic KX-TCD240E Quick Manual preview
KX-TCD240E
Brand: Panasonic Pages: 8
Panasonic KX-TCD220G Quick Manual preview
KX-TCD220G
Brand: Panasonic Pages: 6
Oki OKIFAX 5750 Maintenance Manual preview
OKIFAX 5750
Brand: Oki Pages: 923
Oki OKIFAX 5750 Service Manual preview
OKIFAX 5750
Brand: Oki Pages: 1020
Olivetti Fax_Lab 125 Instructions Manual preview
Fax_Lab 125
Brand: Olivetti Pages: 72
Singer 23-20 Parts List preview
23-20
Brand: Singer Pages: 24
Pfaff 8309-023 Instruction Manual preview
8309-023
Brand: Pfaff Pages: 54
Quasar Autopax PAX600H User Manual preview
Autopax PAX600H
Brand: Quasar Pages: 148
Fastech Ezi-SERVO ST Operating Manual preview
Ezi-SERVO ST
Brand: Fastech Pages: 38
Host Freestyle extractorVAC Safety & Maintenance Instructions preview
Freestyle extractorVAC
Brand: Host Pages: 4
Clarke 9087278020 Instructions For Use Manual preview
9087278020
Brand: Clarke Pages: 135
Rollabind PBS 2000 Operating Instructions preview
PBS 2000
Brand: Rollabind Pages: 2
Singer Cover Stitch Wide User Manual preview
Cover Stitch Wide
Brand: Singer Pages: 13
cimex Cyclone CR38 User Instructions / Parts Manual preview
Cyclone CR38
Brand: cimex Pages: 19
Duerkopp Adler 559 Service Instructions Manual preview
559
Brand: Duerkopp Adler Pages: 77
JUKI DDL-5550N Instruction Manual preview
DDL-5550N
Brand: JUKI Pages: 48

Brands by name

Popular brands

Load more brands