Panasonic KX-FPC135 Service Manual Download Page 8

Page: 8 / 264

1.9. SPECIFICATIONS

These specifications are for the U.S.A. version only. Refer to the simplified manual (cover) for other areas.

■

Main unit

Applicable Lines:

Public Switched Telephone Network

Document Size:

Max. 216 mm (8 1/2") in width

Max. 600 mm (23 5/8") in length

Effective Scanning Width:

208 mm (8 3/16")

Recording Paper Size:

Letter: 216×279 mm (8 1/2"×11")

Legal: 216×356 mm (8 1/2"×14")

Effective Printing Width:

208 mm (8 3/16")

Transmission Time*:

Approx. 9 sec./page (Original mode)**.... KX-FPC141 only,
15 sec./page (Original mode)**.... KX-FPC135 only

Scanning Density:

Horizontal:

8 pels/mm (203 pels/inch)

Vertical:

3.85 lines/mm (98 lines/inch)—STANDARD mode

7.7 lines/mm (196 lines/inch)—FINE/HALF TONE mode

15.4 lines/mm (392 lines/inch)—SUPER FINE mode

Halftone Level:

64-level

Scanner Type:

Contact Image Sensor (CIS)

Printer Type:

Thermal Printing

Data Compression System:

Modified Huffman (MH), Modified READ (MR)

Modem Speed:

14,400/12,000/9,600/7,200/4,800/2,400 bps; Automatic Fallback .... KX-FPC141 only
9,600/7,200/4,800/2,400 bps; Automatic Fallback .... KX-FPC135 only

Operating Environment:

5—35°C (41—95°F), 20—80 % RH(Relative Humidity)

Dimensions (H×W×D):

143×345×305 mm (5 5/8"×13 9/16"×12")

Mass (Weight):

Approx. 4.4 kg (9.7 lb.)

Power Consumption:

Standby: Approx. 11 W

Transmission: Approx. 18 W

Reception: Approx. 42 W (When receiving a 20% black document)

Copy: Approx. 48 W (When copying a 20% black document)

Maximum: Approx. 160 W (When copying a 100% black document)

Power Supply:

120 V AC, 60 Hz (This unit will not function at 50 Hz.)

Memory Capacity:

Voice memory: Approx. 18 minutes of recording time including the greeting
message***.... KX-FPC141 only

Fax memory:

Approx. 28 pages memory reception

Approx. 25 pages memory transmission

(Based on the CCITT of No. 1 Test Chart in standard resolution.)

■

Handset

Operating Environment:

5—35°C (41—95°F), 45—85 % RH(Relative Humidity)

Dimensions (H×W×D):

Approx. 39×55×271 mm (1 17/32"×2 5/32"×10 11/16")

Mass (Weight):

Approx. 200 g (0.4 lb.)

Power Supply:

Ni-Cd battery (3.6 V, 600 mAh)

Frequency:

926 MHz-927 MHz, 902 MHz-903 MHz (30 channels)

Security Codes:

1,000,000

* Transmission speed depends upon the contents of the pages, resolution, telephone line conditions and capability of the receiving
unit.

** The 9 second speed is based upon the CCITT No. 1 Test Chart on the condition that memory transmission is performed. .... KX-
FPC141 only

** The 15 second speed is based upon the CCITT No. 1 Test Chart and original mode. If the capability of the other party´s machine
is inferior to your unit, the transmission time may be longer. .... KX-FPC135 only

*** Recording time may be reduced by the calling party´s background noise. .... KX-FPC141 only

KX-FPC135 / KX-FPC141

Summary of Contents for KX-FPC135









































































































































































































































































Search results

Summary of Contents for KX-FPC135

Reviews:

Related manuals for KX-FPC135

Brands by name

Popular brands

Panasonic KX-FPC135, Service Manual

Search results

Summary of Contents for KX-FPC135

Reviews:

Related manuals for KX-FPC135

Brands by name

Popular brands