manualshive.com logo in svg

Panasonic KX-FPC135, Service Manual

The Panasonic KX-FPC135, an excellent all-in-one fax and phone machine, comes with a comprehensive Operating Instructions Manual to assist users in getting the most out of their device. Easily accessible on our website, this manual is available for free download, granting users the convenience of accessing it whenever needed.

Share
Download
background image

(Cause C)

This model is FAX1 and the other party is FAX2.

For transmission from this model to FAX2, FAX2 executes automatic reception and transmits a CED signal (2100 Hz) followed
by a DIS signal. As the echo cancelers stops as described in cause B, the echo of the DIS signal returns to FAX2. On the other
hand, this model detects the DIS signal and transmits a DCS signal. In other words, it is possible that the echo of the DIS signal
and the DCS signal transmitted from this model reach FAX2 one after the other. FAX2 detects an error and communication
does not start.

(Countermeasure C)

When the international DIS detection setting is set in the service mode (code No.594), this model does not respond to the first
DIS signal and returns a DCS signal only for the second DIS signal.

In other words, there is an interval of 250 msec between transmission of the first and second DIS signal so that the echo
cancelers operation recovers. An echo is not generated for the second DIS signal.

Note:

When the other FAX does not respond with a DCS signal after DIS signal transmission, the DIS signal is transmitted three
times for trial.

Summary:

Symptom/Countermeasure Table (Long distance and international communication operations)

SYMPTOM

COUNTERMEASURE

Does not receive in the automatic mode.

 a. 

If possible, manual transmission should be done from the
transmission side.

 b. 

If possible, two pauses should be inserted at the end of
the auto dial number on the transmission side.

 c. 

If possible, the Function Selector Switch should be
switched to FAX.

Does not transmit.

 a. 

Confirm the international line mode is ON. (Service mode:
code No. 521)

 b. 

Set the international DIS detection. (Service mode: code
No. 594)

Does not receive.

 a. 

Set the time between the CED signal and the DIS signal to
500 msec. (Service mode: code No. 593)

 b. 

Set the CED frequency to 1100Hz. (Service mode: code
No. 520)

 6. The unit can copy, but the transmission and reception image are incorrect.

(Long distance or international communication operation)

This symptom highly depends on the transmission and reception capability of the other FAX unit and the line conditions.

The countermeasures for this unit are shown below.

Transmission Operation:

Set the transmitting speed to 4800BPS (service mode: code No. 717) or select the overseas mode.

Reception Operation:

If 80% or more of the reception is incorrect, set the receiving speed to 4800BPS. (Service mode: code No. 718)

  • 

• 

Refer to 2.4.4. SERVICE FUNCTION TABLE.

56

KX-FPC135 / KX-FPC141

Summary of Contents for KX-FPC135









































































































































































































































































Reviews:

No comments

Related manuals for KX-FPC135

Fastbind Elite Service Bulletin preview
Elite
Brand: Fastbind Pages: 4
Janome 1108 Instruction Book preview
1108
Brand: Janome Pages: 59
Janome 109 Instruction Book preview
109
Brand: Janome Pages: 42
Panasonic KX-TG9120FX Quick Manual preview
KX-TG9120FX
Brand: Panasonic Pages: 6
Panasonic KX-TG8280FX Operating Instructions Manual preview
KX-TG8280FX
Brand: Panasonic Pages: 60
Bartell B424 Owner'S Manual And Parts Book preview
B424
Brand: Bartell Pages: 30
Kärcher KM 70 C Original Instructions Manual preview
KM 70 C
Brand: Kärcher Pages: 21
Janome DM7200 Handbook & Instructions preview
DM7200
Brand: Janome Pages: 68
Singer 45A92 Parts Manual preview
45A92
Brand: Singer Pages: 5
Anita GARUDAN GF-1107-147 MH Manual preview
GARUDAN GF-1107-147 MH
Brand: Anita Pages: 73
Viper 50000572 Instructions For Use Manual preview
50000572
Brand: Viper Pages: 93
Gammill The Charm Quick Start Manual preview
The Charm
Brand: Gammill Pages: 26
Singer 5417C Instruction Book preview
5417C
Brand: Singer Pages: 108
Reliable BARRACUDA 200ZW Instruction Manual preview
BARRACUDA 200ZW
Brand: Reliable Pages: 40
Consew 277RFS-3 Operation Instruction & Parts List preview
277RFS-3
Brand: Consew Pages: 26
Powr-Flite PAS20BA-BC Operator'S Manual preview
PAS20BA-BC
Brand: Powr-Flite Pages: 9
Hefter TF MINI plus Operating Manual preview
TF MINI plus
Brand: Hefter Pages: 20
Hotpoint WMEF 762 Instructions For Use Manual preview
WMEF 762
Brand: Hotpoint Pages: 16

Brands by name

Popular brands

Load more brands