manualshive.com logo in svg

Panasonic KX-FPC135, Service Manual

The Panasonic KX-FPC135, an excellent all-in-one fax and phone machine, comes with a comprehensive Operating Instructions Manual to assist users in getting the most out of their device. Easily accessible on our website, this manual is available for free download, granting users the convenience of accessing it whenever needed.

Share
Download
background image

2.4.6.1. Descriptions of the HISTORY Report

(1) ROM VERSION

EPROM version

(2) SUM

EPROM internal data calculation.

(3) YOUR LOGO

The user logo recorded in the unit. If it is not recorded, NONE will be displayed.

(4) YOUR TELEPHONE NUMBER

The user telephone number recorded in the unit. If it is not recorded, NONE will be displayed.

(5) FAX PAGER NUMBER

If you program a pager number into the unit, the pager number will be displayed here.

(6) FACTORY - CUSTOMER

This shows how many days from factory production until the user turns ON the unit.

(7) MONTH

The shows the very first month, date, year and time set by the user after they purchased the unit.

(8) DAY

The shows the very first month, date, year and time set by the user after they purchased the unit.

(9) YEAR

The shows the very first month, date, year and time set by the user after they purchased the unit.

(10) TIME

The shows the very first month, date, year and time set by the user after they purchased the unit.

(11) USAGE TIME

The amount of time the unit has been powered ON.

(12) FACTORY - NOW

This shows how many days from factory production until the user prints out this history list.

(13) TEL MODE

The amount of time the TEL mode setting was used.

(14) FAX MODE

The amount of time the FAX mode setting was used.

(15) TEL/FAX MODE

The amount of time the TEL/FAX mode setting was used.

(16) ANS/FAX MODE

The amount of time the ANS/FAX mode setting was used.

(17) FINAL RECEIVE MODE

The last set receiving mode by the user.

(18) TONE/PULSE SELECTION

The most recently used setting used, either TONE or PULSE.

(19) RECEIVE REDUCTION

The compression rate when receiving.

(20) SETTING NO. OF DIRECTORY

The recorded directory stations (one touch and JOG DIAL).

(21) NUMBER OF COPY

The number of pages copied.

(22) NUMBER OF RECEIVE

The number of pages received.

(23) NUMBER OF SENDING

The number of pages sent.

(24) NUMBER OF CALLER ID

The number of times Caller ID was received.

108

KX-FPC135 / KX-FPC141

Summary of Contents for KX-FPC135









































































































































































































































































Reviews:

No comments

Related manuals for KX-FPC135

Vector Fog H100 Instruction Manual preview
H100
Brand: Vector Fog Pages: 10
Windsor M17XI Operating Instructions Manual preview
M17XI
Brand: Windsor Pages: 22
National Flooring Equipment 14420 Instruction Manual preview
14420
Brand: National Flooring Equipment Pages: 25
Janome Memory Craft Compulock II Service Manual preview
Memory Craft Compulock II
Brand: Janome Pages: 38
EuroLite NSF-350 User Manual preview
NSF-350
Brand: EuroLite Pages: 32
GBC DocuBind P100 Operating Instructions preview
DocuBind P100
Brand: GBC Pages: 1
A-S-S BASS 2020 Working Instructions preview
BASS 2020
Brand: A-S-S Pages: 7
Tennant T981 Operator'S Manual preview
T981
Brand: Tennant Pages: 41
Kärcher 1.259-005 Instruction Manual preview
1.259-005
Brand: Kärcher Pages: 261
Ricoh Fax 680 MP Service Manual preview
Fax 680 MP
Brand: Ricoh Pages: 84
JUKI HZL-60ce Service Manual preview
HZL-60ce
Brand: JUKI Pages: 20
JUKI HZL-60 CE Instruction Manual preview
HZL-60 CE
Brand: JUKI Pages: 28
JUKI HZL-E70 Instruction Manual preview
HZL-E70
Brand: JUKI Pages: 52
JUKI Exceed F-300 Instruction Manual preview
Exceed F-300
Brand: JUKI Pages: 164
JUKI AMS-221ENTS Instruction Manuals preview
AMS-221ENTS
Brand: JUKI Pages: 135
JUKI LBH-781 Instruction Manual preview
LBH-781
Brand: JUKI Pages: 92
JUKI dsu-142 Instruction Manual preview
dsu-142
Brand: JUKI Pages: 56
Mi-T-M AW-7020-8007 Quick Start Manual preview
AW-7020-8007
Brand: Mi-T-M Pages: 2

Brands by name

Popular brands

Load more brands