manualshive.com logo in svg

Panasonic KX-FPC135, Service Manual

The Panasonic KX-FPC135, an excellent all-in-one fax and phone machine, comes with a comprehensive Operating Instructions Manual to assist users in getting the most out of their device. Easily accessible on our website, this manual is available for free download, granting users the convenience of accessing it whenever needed.

Share
Download
background image

1.13. CONNECTIONS

1.13.1. CONNECTIONS (KX-FPC135)

This connection is for the U.S.A. version only. Refer to the simplified manual (cover) for other areas.

Automatic dialing mode setting 

When the telephone line cord and the power cord are connected, the unit will automatically start to detect
the dialing mode of your telephone line.

Display:

Wait until one of the following messages is displayed.

Your line has touch tone service.

Your line has rotary pulse dial service.

If the power cord is disconnected or a power failure occurs, the unit will detect the dialing mode again when
power is restored.
If you connect the power cord before connecting the telephone line cord, the following messages will be
shown alternately.

Connect the telephone line cord.

(Model KX-FPC135)

INSERT TEL LINE

NO TEL LINE

LINE IS PULSE

LINE IS TONE

CHECKING LINE

Wall jack 
(RJ11C)

120 V, 60 Hz

Telephone 
line cord

Power cord

Power surge
protector

(          )

Line surge
protector

(         )

Connect to “LINE”.

1

Connect the telephone line cord.

2

Connect the power cord.

The unit will automatically start to
detect the dialing mode of your
telephone line (see below).

When the power is turned on for the
first time, the unit will print some
basic information.

Note:

For additional equipment protection, we recommend the use of a surge protector. The following types are
available; TELESPIKE BLOK MODEL TSB (TRIPPE MFG. CO.), SPIKE BLOK MODEL SK6-0 (TRIPPE
MFG. CO.), SUPER MAX (PANAMAX) or MP1 (ITW LINX).
The warranty does not cover damage due to power line surges or lightning.
When
If you went to connect an answering machine to the unit. 

you operate this product, the power outlet should be near the product and easily accessible.

2

1

16

KX-FPC135 / KX-FPC141

Summary of Contents for KX-FPC135









































































































































































































































































Reviews:

No comments

Related manuals for KX-FPC135

Canon FAXPHONE L100 Starter Manual preview
FAXPHONE L100
Brand: Canon Pages: 28
Janome Sewing Machine Operating Instructions Manual preview
Sewing Machine
Brand: Janome Pages: 8
Panasonic KX-FP121 Operating Instruction preview
KX-FP121
Brand: Panasonic Pages: 136
Panasonic UF 890 - Panafax B/W Laser User Manual preview
UF 890 - Panafax B/W Laser
Brand: Panasonic Pages: 174
Janome 15000 Quick Manual preview
15000
Brand: Janome Pages: 5
Pallmann UNO Translation Of The Original Manual preview
UNO
Brand: Pallmann Pages: 36
Taski procarpet 30 User'S & Technical Manual preview
procarpet 30
Brand: Taski Pages: 74
Taski ergodisc 165 Translation Of The Original Instructions Of Use preview
ergodisc 165
Brand: Taski Pages: 7
Savin Savinfax 3670 Operator'S Manual preview
Savinfax 3670
Brand: Savin Pages: 143
Singer 221K Instructions For Using Manual preview
221K
Brand: Singer Pages: 56
Husqvarna Viking Tribute 140C User Manual preview
Tribute 140C
Brand: Husqvarna Viking Pages: 48
Ricoh FAX4000L Operator'S Manual preview
FAX4000L
Brand: Ricoh Pages: 134
Neopost PF-55 User Manual preview
PF-55
Brand: Neopost Pages: 11
JUKI DDL-8300N Instruction Manual preview
DDL-8300N
Brand: JUKI Pages: 49
JUKI L-1C Instruction Manual preview
L-1C
Brand: JUKI Pages: 18
JUKI J-350QVP Instruction Manual preview
J-350QVP
Brand: JUKI Pages: 32
Koblenz B-1500 Operation Instructions preview
B-1500
Brand: Koblenz Pages: 4
BoomToneDJ FOG-700 User Manual preview
FOG-700
Brand: BoomToneDJ Pages: 8

Brands by name

Popular brands

Load more brands