Panasonic KX-FP101AL Service Manual Download

Page: 119 / 206

6.2. GENERAL BLOCK DIAGRAM

The following is an outline of each device IC on the digital board. (Refer to 6.2.1. General Block Diagram.).

1. ASIC (IC501)

Composed mainly of an address decoder and a modem control.

Controls the general FAX operations.

Controls the operation panel I/F.

Controls the thermal head I/F and CIS I/F.

Performs the image processing.

CPU and Real time clock

Provides the reset pulse for each of the major ICs.

2. ROM (IC502)

Contains all of the program instructions on the unit operations.

3. Static RAM (IC504)

This memory is used mainly for the parameter working in the storage area.

4. Dynamic RAM (IC503)

This memory is used mainly for the parameter working in the storage area.

5. MODEM (IC505)

Performs the modulation and the demodulation for FAX communication.

6. Read Section

CIS image sensor to read transmitted documents.

7. Motor Driver (IC506)

Drives the transmission motor and the reception motor.

8. Thermal Head

Contains heat-emitting elements for dot matrix image printing.

9. Analog Board

Composed of ITS circuit and NCU circuit.

10. Sensor Section

Composed of a cover open sensor, a document sensor, a read position sensor, a paper top sensor and a film end sensor.

11. Power Supply Board Switching Section

Su5V and +24V to the unit.

119

KX-FP101AL

Summary of Contents for KX-FP101AL















































































































































































































Search results

Summary of Contents for KX-FP101AL

Reviews:

Related manuals for KX-FP101AL

Brands by name

Popular brands

Panasonic KX-FP101AL, Service Manual

Search results

Summary of Contents for KX-FP101AL

Reviews:

Related manuals for KX-FP101AL

Brands by name

Popular brands