Panasonic KX-FP101AL Service Manual Download

Page: 83 / 206

2.4.4. SERVICE FUNCTION TABLE

Code

Function

Set Value

Effective Range

Default

Remarks

501

Pause time set

X 100 msec

001~600

----------------

502

Flash time set

01~99 X 100 msec

01~99

100

----------------

503

Dial speed select

1:10 pps 2:20 pps

1, 2

----------------

511

Vox sense

1:High 2:Low

1, 2

When the TAM or EXT TAM
does not stop recording the
ICM because noise is detected
on the telephone line, change
this setting to "LOW".

514

Bell detect time set

1~9 X 100 msec

1~9

600

----------------

520

CED frequency select

1:2100 Hz 2:1100 Hz

1, 2

See Symptom/
Countermeasure Table for
long distance and international
calls in 2.3.3.1. Defective
Facsimile Section.

521

International mode select

1:ON 2:OFF

1, 2

See Symptom/
Countermeasure Table for
long distance and international
calls in 2.3.3.1. Defective
Facsimile Section.

522

Auto standby select

1:ON 2:OFF

1, 2

The resolution reverts to the
default when transmission is
complete.

523

Receive equalizer select

1:ON 2:OFF

1, 2

When the telephone station is
far from the unit or reception
cannot be performed correctly,
adjust accordingly.

524

Transmission equalizer select

1:0.0km / 2:1.8km
3:3.6km / 4:7.2km

1~4

----------------

550

Memory clear: To reset the value to the default one, except the top margin (853)
and left margin (854).

"START" input"

552

DTMF single tone test

1:ON 2:OFF

1, 2

See 2.5. TEST FUNCTIONS.

553

Monitor on FAX communication
select

1: OFF 2:PHASE B
3:ALL

1~3

Sets whether to monitor the
line signal with the unit´s
speaker during FAX
communication or not.

554

Modem test

See 2.5. TEST FUNCTIONS.

555

Scan check

See 2.5. TEST FUNCTIONS.

556

Motor test

See 2.5. TEST FUNCTIONS.

557

LED test

See 2.5. TEST FUNCTIONS.

558

LCD test

See 2.5. TEST FUNCTIONS.

559

Document jam detection select

1:ON 2:OFF

1, 2

See 2.2.1. Paper Jam.

561

KEY test

See 2.5. TEST FUNCTIONS.

570

BREAK % select

1:61% 2:67%

1, 2

Sets the % break of pulse
dialing accordingly PBX.

571

ITS auto redial time set

X number of times

00~99

Selects the number of time that
ITS is redialed (not including
the first dial).

572

ITS auto redial line disconnection
time set

X second

001~999

Sets the interval of ITS
redialing.

573

Remote turn-on ring number set

X number of rings

01~99

Sets the number of rings
before the unit starts to receive
a document in the TEL mode.

590

FAX auto redial time set

X number of times

00~99

Selects the number of redial
times during FAX
communication (not including
the first dial).

591

FAX auto redial time disconnection
time set

X second

001~999

Sets the FAX redial interval
during FAX communication.

592

CNG transmit select

1: OFF 2:ALL
3:AUTO

1~3

Lets you select the CNG output
during FAX transmission. ALL:
CNG is output at phase A.
AUTO: CNG is output only
when automatic dialing is
performed. OFF: CNG is not
output at phase A.

593

Time between CED and 300bps

1: 75 msec 2:500
msec 3:1 sec

1~3

See Symptom/
Countermeasure Table for
long distance and international
calls in 2.3.3.1. Defective
Facsimile Section.

KX-FP101AL

Summary of Contents for KX-FP101AL















































































































































































































Search results

Summary of Contents for KX-FP101AL

Reviews:

Related manuals for KX-FP101AL

Brands by name

Popular brands

Panasonic KX-FP101AL, Service Manual

Search results

Summary of Contents for KX-FP101AL

Reviews:

Related manuals for KX-FP101AL

Brands by name

Popular brands