Panasonic KX-FP101AL Service Manual Download Page 6

Page: 6 / 206

1.9. SPECIFICATIONS

Applicable Lines:

Public Switched Telephone Network

Document Size:

Max. 216 mm (8 1/2") in width

Max. 600 mm (23 5/8") in length

Effective Scanning Width:

208 mm (8 3/16")

Recording Paper Size:

A4: 210×297 mm (8 1/4"×11 11/16")

Effective Printing Width:

202 mm (8")

Transmission Time*:

Approx. 12 sec./page (Original mode)**

Scanning Density:

Horizontal:

8 pels/mm (203 pels/inch)

Vertical:

3.85 lines/mm (98 lines/inch)—STANDARD mode

7.7 lines/mm (196 lines/inch)—FINE/HALF TONE mode

15.4 lines/mm (392 lines/inch)—SUPER FINE Mode

Halftone Level:

64-level

Scanner Type:

Contact Image Sensor (CIS)

Printer Type:

Thermal Printing

Data Compression System:

Modified Huffman (MH), Modified READ (MR)

Modem Speed:

9,600/7,200/4,800/2,400 bps; Automatic Fallback

Operating Environment:

5—35°C (41—95°F), 20—80 % RH(Relative Humidity)

Dimensions (H×W×D):

143×325×305 mm (5 5/8"×12 13/16"×12")

Mass (Weight):

Approx. 4.0 kg (8.8 lb.)

Power Consumption:

Standby: Approx. 6.5 W

Transmission: Approx. 15 W

Reception: Approx. 42 W (When receiving a 20% black document)

Copy: Approx. 45 W (When copying a 20% black document)

Maximum: Approx. 150 W (When copying a 100% black document)

Power Supply:

220—240 V AC, 50/60 Hz

Memory Capacity:

Approx. 28 pages memory reception

Approx. 25 pages memory transmission

(Based on ITU-T Test Chart in standard resolution.)

* Transmission speed depends upon the contents of the pages, resolution, telephone line conditions and capability of the receiving
unit.

** The 12 second speed is based upon the ITU-T Test Chart and original mode. (Refer to "1.11. ITU-T Test Chart".) If the capability
of the other party’s machine is inferior to your unit, the transmission time may be longer.

Note:

Any details given in these instructions are subject to change without notice.

The pictures and illustrations in these instructions may vary slightly from the actual product.

Design and specifications are subject to change without notice.

1.10. OPTIONAL ACCESSORIES

KX-FP101AL

Summary of Contents for KX-FP101AL















































































































































































































Search results

Summary of Contents for KX-FP101AL

Reviews:

Related manuals for KX-FP101AL

Brands by name

Popular brands

Panasonic KX-FP101AL, Service Manual

Search results

Summary of Contents for KX-FP101AL

Reviews:

Related manuals for KX-FP101AL

Brands by name

Popular brands