Panasonic KX-FP101AL Service Manual Download

Page: 84 / 206

Code

Function

Set Value

Effective Range

Default

Remarks

594

Overseas DIS detection select

1:detects at the 1st
time 2:detects at the
2st time

1, 2

See Symptom/
Countermeasure Table for
long distance and international
calls in 2.3.3.1. Defective
Facsimile Section.

595

Receive error limit value set

X Number of times

001~999

100

Sets the number of acceptable
error lines when the FAX
reconstructs the received data.

596

Transmit level set

X dBm

- 15~00

Selects the FAX transmission
level.

598

Receiving sensitivity

43= -43 dBm

20~48

See (Countermeasure C) in
2.3.3.1. Defective Facsimile
section

599

ECM frame size

1:256 / 2:64

1, 2

----------------

602

Warning LIST Printing

1:ON 2:OFF

1, 2

Used to print a caution list
when setting the TEL/FAX
mode and ring detection.

717

Transmit speed selection

1:9600BS 2:7200BS
3:4800BS 4:2400BS

1~4

Adjusts the speed to start
training during FAX
transmission.

718

Receive speed selection

1:9600BS 2:7200BS
3:4800BS 4:2400BS

1~4

Adjusts the speed to start
training during FAX reception.

719

Ringer off in TEL/FAX mode

1:ON 2:OFF

1, 2

Sets the ringer switch off when
a call is received in the
TEL/FAX mode.

721

Pause tone detect

1:ON 2:OFF

1, 2

Selects the tone detection for
pauses in dialing.

722

Redial tone detect

1:ON 2:OFF

1, 2

Selects the tone detection
mode after redialing.

745

Poewr ON film feed

1:ON 2:OFF

1, 2

When the power is turned on,
the film is wound to take up
any slack.

763

CNG detect time for friendly
reception

1:10 sec 2:20 sec
3:30 sec

1~3

Selects the CNG detection time
of friendly reception.

771

T1 timer

1:35 sec 2:60 sec

1, 2

Sets a higher value when the
response from the other party
needs more time during FAX
transmission.

774

T4 timer

X 100 msec

00~99

Use this function when delay
occurs on the line and
communication (ex. mobile
comm) does not work well.

815

Sensor & Vox check

See 2.5. TEST FUNCTIONS.

852

Print test pattern

See 2.5. TEST FUNCTIONS.

853

Top margin

1~9

--------

854

Left margin

1~8

--------

861

A4 size set

1:ON 2:OFF

1, 2

Used only at the factory.

880

History list

See 2.4.6. HISTORY.

881

Journal 2 list

See 2.4.7.3.PRINTOUT
EXAMPLE

882

Journal 3 list

See 2.4.7.3.PRINTOUT
EXAMPLE

890

TEL/FAX 1st ring back tone

1:ON 2:OFF

1, 2

Selects whether the TEL/FAX
1st ring back tone is ON or
OFF in the TEL/FAX mode.

KX-FP101AL

Summary of Contents for KX-FP101AL















































































































































































































Search results

Summary of Contents for KX-FP101AL

Reviews:

Related manuals for KX-FP101AL

Brands by name

Popular brands

Panasonic KX-FP101AL, Service Manual

Search results

Summary of Contents for KX-FP101AL

Reviews:

Related manuals for KX-FP101AL

Brands by name

Popular brands