manualshive.com logo in svg

Panasonic i-pro WV-NP1004, Network Operating Instructions, Page: 64 / 73

Share
Download
Panasonic i-pro WV-NP1004 Network Operating Instructions Download Page 64

64

Step 1

Select "ON" for "EL-ZOOM" on the "CAMERA SETUP"
page.

→

The "EL-ZOOM" page will be displayed.

Step 2

Move the cursor onto "ZOOM" and press the [SET] but-
ton.

→

Images to which zooming can be applied will be dis-
played.

Step 3

Adjust zooming level pressing the [Up] and [Down] but-
tons. After completing the adjustment, press the [SET]
button.

→

The "EL-ZOOM" page will be displayed.

Step 4

Move the cursor onto "PAN/TILT" and press the [SET]
button.

→

Images to which panning/tilting can be applied will
be displayed.

Important:

"PAN/TILT" is available only when images are
zoomed in.

Step 5

Adjust panning/tilting level pressing the [Left], [Right],
[Up] and [Down] buttons. After completing the adjust-
ment, press the [SET] button.

→

The "EL-ZOOM" page will be displayed.

Note:

When "ON" is selected for "EL-ZOOM", "PAN/TILT"
and "ZOOM" are operable using a system controller.

Adjust the electronic zoom

The electronic zoom is operable using a remote controller.

      **EL-ZOOM** 
   
PAN/TILT      PUSH SW
ZOOM          PUSH SW

 
 RET TOP END

      **EL-ZOOM** 
   
PAN/TILT      PUSH SW
ZOOM          PUSH SW

   U ZOOM D

 
 RET TOP END

      **EL-ZOOM** 
   
PAN/TILT      PUSH SW
ZOOM          PUSH SW
   U TILT D/L PAN R

 
 RET TOP END

Summary of Contents for i-pro WV-NP1004










































































Reviews:

No comments