Panasonic GLOBARANGE BB-GT1500E Operating Instructions Manual Download Page 102

Page: 102 / 112

Useful Information

102

For product assistance, visit www.globarange.com

For

assistance, visit www.joip.com

Specifications

■

Standard:

DECT (Digital Enhanced Cordless
Telecommunications),
GAP (Generic Access Profile)

■

Number of channels:

120 Duplex Channels

■

Frequency range:

1.88 GHz to 1.9 GHz

■

Duplex procedure:

TDMA (Time Division Multiple Access)

■

Channel spacing:

1,728 kHz

■

Bit rate:

1,152 kbit/s

■

Modulation:

GFSK (Gaussian Frequency Shift
Keying)

■

RF transmission power:

Approx. 250 mW

■

Power source:

220–240 V AC, 50 Hz

■

Network interface:

10/100base-TX auto MDI/MDIX
Ethernet LAN port

■

Support codecs:

G.711

-law, G.711 A-law, G.726 (32k),

G.729A

■

Power consumption:

Base unit:
BB-GT1500

Standby: Approx. 3.0 W
Maximum: Approx. 6.5 W

BB-GT1520/BB-GT1522

Standby: Approx. 3.0 W
Maximum: Approx. 6.5 W

BB-GT1540

Standby: Approx. 3.0 W
Maximum: Approx. 6.9 W

Charger:

Standby: Approx. 1.1 W
Maximum: Approx. 5.2 W

■

Operating conditions:

C–40

C, 20 %–80 % relative air

humidity (dry)

■

Dimensions:

Base unit:

Approx. 82 mm

189 mm

129 mm

Handset:

Approx. 156 mm

48 mm

Charger:

Approx. 68 mm

82 mm

■

Mass (weight):

Base unit:
BB-GT1500

Approx. 310

BB-GT1520/BB-GT1522

Approx. 360

BB-GT1540

Approx. 390

Handset:

Approx. 160

Charger:

Approx. 80

Note:

Design and specifications are subject
to change without notice.

The illustrations in these instructions
may vary slightly from the actual
product.

GT15xxE.book Page 102 Wednesday, August 1, 2007 11:59 AM

Summary of Contents for GLOBARANGE BB-GT1500E

















































































































Search results

Summary of Contents for GLOBARANGE BB-GT1500E

Reviews:

Related manuals for GLOBARANGE BB-GT1500E

Brands by name

Popular brands

Panasonic GLOBARANGE BB-GT1500E, Operating Instructions Manual

Search results

Summary of Contents for GLOBARANGE BB-GT1500E

Reviews:

Related manuals for GLOBARANGE BB-GT1500E

Brands by name

Popular brands