Panasonic GLOBARANGE BB-GT1500E Operating Instructions Manual Download Page 83

Page: 83 / 112

Useful Information

For product assistance, visit www.globarange.com

For

assistance, visit www.joip.com

No link to base. Move
closer to base, try
again.

The handset has lost communication with the
base unit. Move closer to the base unit, and
try again.

Unplug the base unit’s AC adaptor to reset the
unit. Reconnect the adaptor and try again.

The handset’s registration may have been
cancelled. Re-register the handset (page 77).

Phonebook Memory Full

There is no space to store new items in the
phonebook. Erase unnecessary items (page
41).

Please hang up and try
again.

A handset button was pressed while the
handset was on the base unit or charger. Lift
the handset and press the button again.

Please read joip Terms
of Use. Agree?

You have not agreed to the Terms of Use for
the

services. To use the

IP line, you

need to agree to it using the handset (page
19).

This message is not
erasable.

The protected messages remain. All other
messages are erased.

This message contains
invalid characters.

The characters the unit cannot recognise are
replaced with “_”.

*1 BB-GT1520/BB-GT1522/BB-GT1540

Display message

Cause/solution

GT15xxE.book Page 83 Wednesday, August 1, 2007 11:59 AM

Summary of Contents for GLOBARANGE BB-GT1500E

















































































































Search results

Summary of Contents for GLOBARANGE BB-GT1500E

Reviews:

Related manuals for GLOBARANGE BB-GT1500E

Brands by name

Popular brands

Panasonic GLOBARANGE BB-GT1500E, Operating Instructions Manual

Search results

Summary of Contents for GLOBARANGE BB-GT1500E

Reviews:

Related manuals for GLOBARANGE BB-GT1500E

Brands by name

Popular brands