Panasonic EverVolt EVAC-105-6 Installation & Service Manual Download Page 53

Page: 53 / 99

Installation Manual

Connecting the SmartHub to the Internet

ASSEMBLY (Continued)

8. Connecting the SmartHub to the Internet

Hardwire LAN

Connecting the Internet - Ethernet Powerline Adapter (PLC)

1. Unbox the Powerline Connector (PLC).

2. Plug the first PLC into an outlet

near the installed EverVolt.

3. Run a CAT5/6 cable from the SmartHub to the PLC.

4. Place the second PLC next to the customer's router.

5. Run a CAT5/6 from the PLC to the customer's router.

6. For full installation instructions, refer to 'Quick Start' booklet located

in the PLC box.

Run a CAT5/6 cable from the RJ45 router to the RJ45 SmartHub connector.

Ethernet Powerline

Adapter (PLC)

Ensure PLC power supply and the internet connection's is fed from essential loads panel.

Summary of Contents for EverVolt EVAC-105-6




































































































Search results

Summary of Contents for EverVolt EVAC-105-6

Reviews:

Related manuals for EverVolt EVAC-105-6

Brands by name

Popular brands

Panasonic EverVolt EVAC-105-6, Installation & Service Manual

Search results

Summary of Contents for EverVolt EVAC-105-6

Reviews:

Related manuals for EverVolt EVAC-105-6

Brands by name

Popular brands