Panasonic EverVolt EVAC-105-6 Installation & Service Manual Download Page 52

Page: 52 / 99

Installation Manual

Installing the SmartHub

Step 4.

Insert the USB flash drive into the

SmartHub

Step 5.

Internet Connection. There are three ways to establish an internet

connection: LAN, PLC or Cellular (NOT INCLUDED).

LAN Connection (PREFERRED)

Connect the ethernet cable to the

SmartHub and to the network/router.

Cellular Connection (NOT INCLUDED)

Connect a non password protected

3G/4G dongle to the SmartHub.

Step 6.

Connect the power adapter into the SmartHub and then to the power outlet.

Note: The power outlet needs to be a backed up

so the SmartHub will still work when there is no grid.

Summary of Contents for EverVolt EVAC-105-6




































































































Search results

Summary of Contents for EverVolt EVAC-105-6

Reviews:

Related manuals for EverVolt EVAC-105-6

Brands by name

Popular brands

Panasonic EverVolt EVAC-105-6, Installation & Service Manual

Search results

Summary of Contents for EverVolt EVAC-105-6

Reviews:

Related manuals for EverVolt EVAC-105-6

Brands by name

Popular brands