manualshive.com logo in svg

Panasonic DLP PT-FRZ50, Operating Instructions Manual

Share
Download
Panasonic DLP PT-FRZ50 Operating Instructions Manual Download Page 47

Chapter 3 

 

Basic Operations — Switching on/off the projector

ENGLISH - 47

 

f

Even when the power <

v

/

b

> button is pressed and the projector is switched off, the projector consumes power if the main power 

of the projector is on.

When the [PROJECTOR SETUP] menu 

→

 [ECO MANAGEMENT] 

→

 [STANDBY MODE] is set to [ECO], use of some functions is restricted, 

but the power consumption during standby mode can be conserved.

 

f

While projecting, the power can be turned off by pressing the <OFF> side of the <MAIN POWER> switch, or by directly using the breaker 

under conditions where the <MAIN POWER> switch of the projector cannot be switched off/on easily such as while installing on the ceiling. 

However, the settings or adjustments performed right before the power is turned off may not be reflected.

Summary of Contents for DLP PT-FRZ50



























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands