Panasonic DLP PT-FRZ50 Operating Instructions Manual Download Page 162

Page: 162 / 186

Chapter 6

Maintenance — Troubleshooting

162 - ENGLISH

Problems

Points to be checked

Page

Video from HDMI

compatible device does

not appear or it appears

jumbled.

Is the HDMI cable connected securely?

Turn the power of the projector and the external device off and on.

―

Is a signal which is not compatible with the projector being input?

176

Cannot control the

projector with Art-Net.

Are the connections between the twisted-pair-cable transmitter and an external

device, and between the twisted-pair-cable transmitter and projector correctly done?

―

Is [Art-Net SETUP] set to other than [OFF]?

127

Are [NET], [SUB NET], [UNIVERSE], and [START ADDRESS] set correctly?

127

The DIGITAL LINK input

image is not displayed.

Is the cable compatible to the condition of the projector used?

Are the connections between the twisted-pair-cable transmitter and an external

device, and between the twisted-pair-cable transmitter and projector correctly done?

―

Is [DIGITAL LINK MODE] set to [AUTO], [DIGITAL LINK], or [LONG REACH]? Is it

set to [ETHERNET]?

120

Is a signal which is not compatible with a twisted-pair-cable transmitter being input?

―

Attention

If problems persist even after checking the preceding points, consult your dealer.

Summary of Contents for DLP PT-FRZ50



























































































































































































Search results

Summary of Contents for DLP PT-FRZ50

Reviews:

Brands by name

Popular brands

Panasonic DLP PT-FRZ50, Operating Instructions Manual

Search results

Summary of Contents for DLP PT-FRZ50

Reviews:

Brands by name

Popular brands