Panasonic CS-F24DTE5 Service Manual Download Page 82

Page: 82 / 145

[Manual setting]

10.7.5.

Emergency operation

• If you do not have the wireless remote controller (because the batteries are weak, or some other reason prevents the wireless

remote controller from being used), emergency operation can be carried out at receptor unit.

• Press the AUTO switch to start emergency operation.

Press the AUTO switch once more to stop emergency operation.

• Press the AUTO switch continue 5 seconds to start cooling operation.

Again press the AUTO switch continue 5 seconds to start heating operation.

• The setting temperature, fan speed and louver control will be fixed at the settings shown in the table below.
• While the indoor unit is running, the OPERATION indicator on the receptor unit will illuminate, and it will switch off when the

indoor units stops.

• Heating operation is not available for indoor units which are for cooling only. (If set to HEAT, the setting will change to FAN

instead.)

Please refer to the instruction manual provided with the indoor unit for instruction on how to use the wireless remote controller.

Operation mode

Fan speed

Louver

Cooling

Previous setting

Heating

Previous setting

Instructions for users

Summary of Contents for CS-F24DTE5


















































































































































Search results

Summary of Contents for CS-F24DTE5

Reviews:

Panasonic CS-F24DTE5, Service Manual, Page: 82 / 145

Search results

Summary of Contents for CS-F24DTE5

Reviews: