manualshive.com logo in svg

Panasonic CS-F24DTE5, Service Manual, Page: 60 / 145

Share
Download
Panasonic CS-F24DTE5 Service Manual Download Page 60

60

b. Prevention measure for refrigerant piping

Prevention measure for refrigerant piping is very important work to prevent water-dust-rubbish from getting in. All
piping terminals needs sealing such as shown below.

• How to pinch

Close terminal part of piping with pliers and seal the gap with brazing.

• How to tape

Seal terminal part of piping with vinyl tape.

3. Vacuum pumping

The purpose of vacuum pumping work is to remove and dry air inside the piping or nitrogen at air tightness test.
Perform the work carefully.

4. Refrigerant filling

Refrigerant filling must be done in the state of liquid refrigerant. If this is done in gas refrigerant, the balance of refrigerant
composition will collapse and damage the operation.

Place

Period of work

Method of seal

Outside

More than 1 month

Pinch

Less than 1 month

Pinch or taping

Inside

Not specified

 Caution

Use the vacuum pump with the backflow prevention mechanism to prevent backflow of oil.

Vacuuming time

60 minutes or more

Vacuum  pump  capacity
60 l/min or more

Summary of Contents for CS-F24DTE5


















































































































































Reviews:

No comments