Panasonic CS-F24DTE5 Service Manual Download Page 80

Page: 80 / 145

10.7.4.

Address setting for wireless remote controller and receptor unit (only when using
more than one indoor unit)

• Only the air conditioner units which receptor unit address numbers match the remote controller address number can be

operated.

• At the time of shipment from the factory, the address numbers for both the wireless remote controller and the receptor unit are

set to “1”. (When using only one indoor unit, the indoor unit can be used without changing the factory default settings.)

Press the address setting switch with a ballpoint pen or similar object to change the address setting.
The address number displayed on the LCD change in the order [ADDRESS 1]

→

[ADDRESS 2]

→

[ADDRESS 3]

→

[GROUP]

→

[ADDRESS 1] each time the switch is pressed.

Summary of Contents for CS-F24DTE5


















































































































































Search results

Summary of Contents for CS-F24DTE5

Reviews:

Panasonic CS-F24DTE5, Service Manual, Page: 80 / 145

Search results

Summary of Contents for CS-F24DTE5

Reviews: