Panasonic CS-F24DTE5 Service Manual Download Page 57

Page: 57 / 145

10.4.11. Check the following items when installation is complete

• After completing work, be sure to measure and record trial run properties, and store measuring data, etc.
• Measuring items are room temperature, outside temperature, suction temperature, blow out temperature, wind velocity, wind

volume, voltage, current, presence of abnormal vibration and noise, operating pressure, piping temperature, compressive
pressure, airtight pressure.

• As to the structure and appearance, check the following items.

M3...69-98 N.cm {7-10 kgf.cm}
M4...157-196 N.cm {16-20 kgf.cm}
M5...196-245 N.cm {20-25 kgf.cm}

10.4.12. Hand over

• Teach the customer the operation and maintenance procedures, using the operation manual (air filter cleaning, temperature

control, etc.)

As to parts to be sold separately

• With regards to installation of the parts sold separately, follow the installation manual which is provided with the parts sold

separately

As for work specifications of the outdoor unit, read the OUTDOOR UNIT INSTALLATION MANUAL attached to the outdoor
unit.

Is circulation of air adequate?

Is draining smooth?

Is heat insulation complete (refrigerant and drain piping)?

Is there any leakage of refrigerant?

Is remote control switch operated?

Is there any faulty wiring?

Are the terminal screws loosened?

Summary of Contents for CS-F24DTE5


















































































































































Search results

Summary of Contents for CS-F24DTE5

Reviews:

Panasonic CS-F24DTE5, Service Manual, Page: 57 / 145

Search results

Summary of Contents for CS-F24DTE5

Reviews: