Panasonic CS-F14DD3E5 Service Manual Download Page 60

Page: 60 / 105

[Manual Setting]

Automatic address resetting for group control

•

The address settings for group control (air conditioner Nos. 1 to 16) can be reset automatically.

1. When operation is stopped, press for 5 seconds, continue the TEST RUN switch to display “00” (will be LOCAL MODE).

2. Press the UP (TEMP) DOWN (TEMP) switch to display 10.

3. Press the SELECT switch to display “000”. It would blinks.

4. Press the UP (TIMER) DOWN (TIMER) switch to display “001”. It would blinks.

5. Press the SET switch.

Switching the thermistor

•

The temperature detection thermistor can be switched between the thermistor at the indoor unit and the thermistor at the
remote controller. However, do not switch to the remote controller thermistor if using two remote controllers.

1. When operation is stopped, press for 5 seconds, continue the TEST RUN switch to display “00” (will be LOCAL MODE).

2. Press the UP (TEMP) DOWN (TEMP) switch to display 11.

3. Press the SELECT switch to display “000”. It would blinks.

4. Press the UP (TIMER) DOWN (TIMER) switch to choose display “000” or “001”.

“000”... Indoor unit setting (factory default)

“001”... Remote controller setting

5. Press the SET switch. (Be sure to press the SET switch so that normal operation mode can be resumed.)

•

Repeat the procedure in steps (1) to (5) to change the setting again.

Summary of Contents for CS-F14DD3E5










































































































Search results

Summary of Contents for CS-F14DD3E5

Reviews:

Panasonic CS-F14DD3E5, Service Manual, Page: 60 / 105

Search results

Summary of Contents for CS-F14DD3E5

Reviews: