Panasonic CS-E9SD3UAW Service Manual Download Page 80

Page: 80 / 124

15.5.9 H27 (Outdoor Air Temperature Sensor Abnormality)

Malfunction Decision Conditions



During startup and operation of cooling and heating, the temperatures detected by the outdoor air temperature

sensor are used to determine sensor errors.

Malfunction Caused



Faulty

connector

connection.



Faulty

sensor.



Faulty

PCB.

Troubleshooting

When abnormality indication starts again

Check the outdoor air temperature sensor:
●

Plug out connector from t he outdoor unit PCB

●

Measure the resistance of the outdoor air temperature
sensor

For safety reason and to prevent component
breakdown, always switch off the power
before remove and connect the component.

Is the measured resistance of the outdoor air temperature
sensor matches the value specified in its characteristic
chart?

●
●

Replace the outdoor air temperature sensor

●

Defect in outdoor unit PCB

●

Replace the outdoor unit PCB

Check the connector connection:
●

Turn off the power

●

Check the connector connection

Is the connector connection normal?

YES

●

Connector poor contact

●

Correct the connection

YES

Defect in outdoor air temperature sensor

Sensor (Thermistor)

Characteristics

(kΩ)

Temperature (ºF)

1 Outdoor Air Sensor
2 Outdoor Heat Exchanger
Sensor

Caution

104

122

Summary of Contents for CS-E9SD3UAW





























































































































Search results

Summary of Contents for CS-E9SD3UAW

Reviews:

Panasonic CS-E9SD3UAW, Service Manual, Page: 80 / 124

Search results

Summary of Contents for CS-E9SD3UAW

Reviews: