Panasonic CS-E9SD3UAW Service Manual Download Page 75

Page: 75 / 124

15.5.4 H15 (Compressor Temperature Sensor Abnormality)

Malfunction Decision Conditions



During startup and operation of cooling and heating, the temperatures detected by the outdoor compressor

temperature sensor are used to determine sensor errors.

Malfunction Caused



Faulty

connector

connection.



Faulty

sensor.



Faulty

PCB.

Troubleshooting

Compressor Temp. Sensor

(Thermistor) Characteristics

Temperature (

Resistance (kΩ)

104

140

176

212

248

284

When abnormality indication starts again

Check the outdoor compressor temperature sensor:
●

Plug out connector from t he outdoor unit PCB

●

Measure the resistance of the outdoor compressor
temperature sensor

For safety reason and to prevent component
breakdown, always switch off the power
before remove and connect the component.

Is the measured resistance of the outdoor compressor
temperature sensor matches the value specified in its
characteristic chart?

●
●

Replace the outdoor compressor temperature sensor

●

Defect in outdoor unit PCB

●

Replace the outdoor unit PCB

Check the connector connection:
●

Turn off the power

●

Check the connector connection

Is the connector connection normal?

YES

●

Connector poor contact

●

Correct the connection

YES

Defect in outdoor compressor temperature sensor

Caution

Summary of Contents for CS-E9SD3UAW





























































































































Search results

Summary of Contents for CS-E9SD3UAW

Reviews:

Panasonic CS-E9SD3UAW, Service Manual, Page: 75 / 124

Search results

Summary of Contents for CS-E9SD3UAW

Reviews: