manualshive.com logo in svg

Panasonic CS-E9SD3UAW, Service Manual, Page: 37 / 124

Share
Download
Panasonic CS-E9SD3UAW Service Manual Download Page 37

37 

In Case of Bottom Intake 

 

1  Remove the frame filter assy as shown in 

diagram 

1

 

2  Remove cover plate as shown in diagram 

1

 

3  Fix frame filter assy as shown in diagram 

2

 

4  Fix cover plate as shown in diagram 

2

 with 

the dummy hole downward. 

 

 

 

 

 

 

1

2

Dummy hole

Dummy hole

Air intake

Air intake

Frame 
Filter 
Assy

Air 

discharge

Air discharge

Cover plate

Cover plate

Frame Filter 
Assy

 

 

Fixing Frame Filter Assy 

 

*  Attach the frame fi lter assy to 

the main unit while pushing the 
tip of the latches in the direction 
of the arrow.

In case of bottom side

Main unit

Filter Assy

In case of back side

 

 

Ceiling Opening 

 

  Install inspection opening 17 23/32" x 17 23/32" (450 mm x 450 mm) on the control box side where maintenance 

and inspection of the control box and drain pump are easy. Install another inspection opening 31 1/2" x 27 9/16" 
(800 mm x 700 mm) also at the lower part of the unit. 

 

 

 

 

  

 

700

800

Allow view A 

Inspection access 

(Field supply)

 

   

 

Air intake

Air 

discharge

Ceiling

A

27 

9/16

" (700)

31 

1

/2

" (800)

 

 

Securing the Hanging Bolts 

 

Wooden of other structure

(Hanging bolt pitch)

C channel

Hanging fi xture

Hanging bolt

Appro

x

.

 4 

1

/2

" (144)

Hanging 
bolt M10

Ceiling surface

Roof beam

Reinforcing materials 

(2 

3/8

" to

 

3 

17/32

") (60 to 90 mm)

Hanging 
bolt M10

Appro

x

. 

4 

1

/2" (114)

Ceiling surface

Insert hole-in 
anchor, etc.

Reinforced concrete

”

1 

9/16

" (40)

t = 

3/32

" (2)

1 

3/16

" (30)

 

 

  Secure the hanging bolts (M10, locally purchased) firmly in a manner capable of supporting the unit weight. 

  Consult your construction or interior contractor for details on finishing the ceiling opening. 

 
 
 
 
 
 
 
 
 

Summary of Contents for CS-E9SD3UAW





























































































































Reviews:

No comments