manualshive.com logo in svg

Panasonic CS-E9SD3UAW, Service Manual, Page: 78 / 124

Share
Download
Panasonic CS-E9SD3UAW Service Manual Download Page 78

78 

15.5.7  H23 (Indoor Pipe Temperature Sensor Abnormality) 

Malfunction Decision Conditions 

  During startup and operation of cooling and heating, the temperatures detected by the indoor heat exchanger 

temperature sensor are used to determine sensor errors. 

 
Malfunction Caused 

 Faulty 

connector 

connection. 

 Faulty 

sensor. 

 Faulty 

PCB. 

 
Troubleshooting 

 

Sensor (Thermistor)

Characteristics

70

60

50

R

e

si

sta

nce

(k

Ω

)

Temperature (ºF)

40

30

20

10

0

1 Pipe temp. Sensor
2 Intake Air Temp. Sensor

1

2

When abnormality indication starts again

Check the outdoor air temperature sensor:
●

Plug out connector from t he outdoor unit PCB

●

Measure the resistance of the outdoor intake air
temperature sensor

For safety reason and to prevent component
breakdown, always switch off the power
before remove and connect the component.

Is the measured resistance of the outdoor intake air
temperature sensor matches the value specified in its
characteristic chart?

●
●

Replace the outdoor intake air temperature
sensor

●

Defect in outdoor unit PCB

●

Replace the outdoor unit PCB

Check the connector connection:
●

Plug out connector from the indoor unit PCB

●

Measure the resistance of the indoor pipe temperature
sensor

Is the connector connection normal?

YES

●

Connector poor contact

●

Correct the connection

NO

NO

YES

Defect in outdoor intake air temperature sensor

Caution

14

32

50

68

86

104

122

 

 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for CS-E9SD3UAW





























































































































Reviews:

No comments