Panasonic CS-E9SD3UAW Service Manual Download Page 46

Page: 46 / 124



For model E18SD3UAW

1 Remove control board cover (Resin and

Metal).

2 Remove particular plate.
3 Remove

plugs.

4 Fix the conduit connectors to the knockout

holes with lock-nuts, then secure them against
the side panel.

5 All wires pass through conduits & particular

plate’s opening hole.

6 Connecting wire between indoor unit and

outdoor unit should be UL listed or CSA
approved 4 conductor wires minimum AWG16
in accordance with local electric codes.

7 Wire connection to the power supply

(208/230V 60Hz) through circuit breaker.

Connect the UL listed or CSA approved
wires minimum AWG12 to the terminal
board, and connect the other end of the
wires to ELCB / GFCI.

Control Board
Cover (Metal)

Lock Nuts

Knockout
Holes

Plugs

Connectors

Control Board
Cover (Resin)

Front Panel

Connecting Wires

Particular Plate’s

opening holes

Particular

Plate

8 Connect the power supply cord and connecting wire between indoor unit and outdoor unit according to the

diagram below.

Outdoor Unit

L1
L2

Terminal

Indoor Unit

Disconnect
Switch
Field supply

Grounding wire

Grounding wire min AWG16

Power Supply
Single Phase
208/230V 60Hz
min AWG12

208/230V min AWG16

* Ensure all connecting wire

between indoor unit and
outdoor unit and power supply
cord are installed in individual
conduit.

9 Secure the wire onto the control board with the holder (clamper).
10 After completing wiring connections, reattach the particular plate and control board cover (metal and resin) to

the original position with the screws.

11 For wire stripping and connection requirement, refer to instruction 11.1.6 of indoor unit.

Power

supply cord

Indoor & outdoor
connection cable

Terminal

Board

Terminal

Board

Holder

Earth
wire
longer
than
others
AC wires
for safety
reasons

WARNING

This equipment must be properly earthed.



Earth lead wire shall be Yellow/Green (Y/G) in colour and longer than other lead wires for electrical safety in case

of the slipping.

Summary of Contents for CS-E9SD3UAW





























































































































Search results

Summary of Contents for CS-E9SD3UAW

Reviews:

Panasonic CS-E9SD3UAW, Service Manual, Page: 46 / 124

Search results

Summary of Contents for CS-E9SD3UAW

Reviews: