Panasonic CJ-HDR216 User Manual Download Page 92

Page: 92 / 212



Anti-dither: Here you can set anti-dither time. The value ranges from 5 to 600s. The

anti-dither time refers to the alarm signal lasts time. It can be seem as the alarm

signal activation stays such as the buzzer, tour, PTZ activation, snapshot, channel

record. The stay time here does not include the latch time. During the alarm process,

the alarm signal can begin an anti-dither time if system detects the local alarm again.

The screen prompt, alarm upload, email and etc. will not be activated. For example, if

you set the anti-dither time as 10 second, you can see the each activation may last

10s if the local alarm is activated. During the process, if system detects another local

alarm signal at the fifth second, the buzzer, tour, PTZ

activation, snapshot, record

channel will begin another 10s while the screen prompt, alarm upload, email will not

be activated again. After 10s, if system detects another alarm signal, it can generate

an alarm since the anti-dither time is out.



Alarm output: when an alarm occurs, system enables peripheral alarm devices.



Latch: when motion detection complete, system auto delays detecting for a specified

time. The value ranges from 1-300(Unit: second)



Show message: System can pop up a message to alarm you in the local host screen if

you enabled this function.



Alarm upload: System can upload the alarm signal to the network (including alarm

center) if you enabled current function.



Send email: System can send out email to alert you when an alarm occurs.



Record channel: System auto activates motion detection channel(s) to record once an

alarm occurs. Please make sure you have set MD record in Schedule interface(Main

Menu -> Setting -> Storage -> Schedule) and schedule record in Record interface

(Main Menu -> Setting -> Storage -> Record)



PTZ activation: Here you can set PTZ movement when an alarm occurs. Such as go

to preset, tour &pattern when there is an alarm. Click

“

Setup

”

button, you can see an

interface is shown as in Figure

‎

4-74



Delay: System can delay the record for specified time after alarm ended. The value

ranges from 10s to 300s.



Tour: Here you can enable tour function when alarm occurs. System one-window tour.



Snapshot: You can enable this function to snapshot image when a motion detect

alarm occurs.



Buzzer: Select the checkbox to enable this function. The buzzer beeps when alarm

occurs.

Please select the checkbox

to select the corresponding function. After all the setups

please click save button, system goes back to the previous menu.

Note:

In motion detection mode, you cannot use copy/paste to set channel setup since the video

in each channel may not be the same.

In Figure

‎

4-73

, you can left click mouse and then drag it to set a region for motion detection.

Click Fn to switch between arm/withdraw motion detection. After setting, click Enter to

exit.

Summary of Contents for CJ-HDR216





















































































































































































































Search results

Summary of Contents for CJ-HDR216

Reviews:

Brands by name

Popular brands

Panasonic CJ-HDR216, User Manual

Search results

Summary of Contents for CJ-HDR216

Reviews:

Brands by name

Popular brands