Panasonic AJ-SD965p, Operating Instructions Manual

Page: 72 / 86

72
H04
F LOADING
Displays the number of times front loading has
been performed in single units.
H05
LCD ON
Displays the time that the LCD monitor has been
lighting in one-hour units.
H15
LCD ONr
Displays the time that the LCD monitor has been
lighting in one-hour units.
(Can be reset)
$ Displaying the “HOURS METER”
information
Turn the search dial to move the cursor (
2
).
The description for the item where the cursor is located
is shown on the counter display.
If “T&S&M” is selected in the setup menu No. 008
(DISPLAY SEL), a message appears in the mode
display whenever a warning or error occurs. When
multiple events occur, the event with the highest
priority is displayed.
<Notes>
O
The resettable items in the “HOURS METER”
information are reset by the shop when performing
maintenance or other work.
O
The search buttons and the search dial cannot be
operated while the DIAG menu is displayed.
Error messages
(continued)
No./Item Description
Ser
222222222
Displays the unit’s serial No.
Priority Display/Description
High
Low
Error messages (See error message table)
When an operational malfunction has occurred in the
unit, the error number flashes and the error message
is indicated on the counter display.
INT SG
When SG has been selected as the input signal with
the INPUT SELECT buttons, pressing the REC
button or the EDIT button (E-E mode) will display
“INT SG” for the first two seconds.
This is also displayed for the first two seconds when
starting editing.
NO INPUT
If there is no input signal (except for analog audio) to
the connector selected using the INPUT SELECT
buttons, pressing the REC button or the EDIT button
(E-E mode) will display “NO INPUT” for the first two
seconds.
This is also displayed for the first two seconds when
starting editing.
Warning messages (See error message table)
When a warning occurs in this unit, the error number
and warning message are indicated on the counter
display.
When multiple warnings occur, the warning with the
highest priority is displayed.
H00
OPERATION
Displays the time that the power has been
supplied in one-hour units.
H01
DRUM RUN
Displays the time that the drum has been
rotating in one-hour units.
H02
TAPE RUN
Displays the time that the tape has been running
during FF, REW, PLAY, SEARCH (JOG, SLOW,
SHTL), REC, and EDIT modes (except for
STILL in the JOG, SLOW or SHTL mode) in
one-hour units.
H03
THREADING
The number of times for threading (loading)/
unthreading (unloading) is displayed in single
units.
H11
DRUM RUNr
Displays the time that the drum has been
rotating in one-hour units. (Can be reset)
H13
THREADINGr
The number of times for threading (loading)/
unthreading (unloading) is displayed in single
units. (Can be reset)
H30
POWER ON
The number of times the power has been turned
on is displayed in single units.
H12
TAPE RUNr
Displays the time that the tape has been running
during FF, REW, PLAY, SEARCH (JOG, SLOW,
SHTL), REC, and EDIT modes (except for
STILL in the JOG, SLOW or SHTL mode) in
one-hour units. (Can be reset)
H14
F LOADINGr
Displays the number of times front loading has
been performed in single units.
(Can be reset)
$ UMID information display
This is displayed when UMID information is present on
the input signal in E-E mode.
This lamp lights during tape playback when UMID
information has been recorded on the tape.
“NO-INFO” is displayed when there is no UMID
information.
Item Display/Description
MATNO Material number
COPY Instance number (No. of copies)
OWNR Country, organization, user
POS Reception status from GPS satellites when
recording spatial coordinates (height above sea
level, longitude and latitude):
HOLD: No reception from any satellite
2D:
Reception possible, but number of
satellites is insufficient. Height above
sea level will not be accurate.
3D: Good reception
DATE Date
TIME UTC (Coordinated Universal Time) and time
difference with UTC