Panasonic AJ-SD965p Operating Instructions Manual Download Page 65 | Manualshive

Page: 65 / 86

background image

65

Video output signals and servo reference signal

This section explains how the output signals and servo
reference signal are selected.

External synchronization of video
output signals

The video output signals are output in synchronization
with the REF VIDEO input signal or video input signal.
As shown in the figure below, this signal is selected in
accordance with the setup menu settings, VTR mode
and availability of the video input signal.

<Notes>

Synchronization is determined as follows depending
on the availability of the REF VIDEO input signal when
“BB”, “CB100” or “CB75” has been selected as the
setup menu No. 600 (INT SG) setting.

O

When the REF VIDEO input signal is available:

Synchronization with the REF VIDEO input signal

O

When the REF VIDEO input signal is not available:

Internal synchronization

Start

What is the

setup menu No. 304 (SERVO

REF) setting?

EXT

Is the unit

in one of the editing

modes?

YES

Has the unit

been set to the recording

mode?

YES

AUTO/AUTO1

What is the

setup menu No. 601 (OUT

VSYNC) setting?

Is the

video input signal available?

N-VF

YES

VF

What is the

setup menu No. 304 (SERVO

REF) setting?

AUTO

AUTO1

NO

NO

Is the

REF VIDEO input signal

available?

Internal synchronization

Synchronization with the

REF VIDEO input signal

Synchronization with

the video input signal

YES

NO

Is the

REF VIDEO input signal

available?

NO

NO

NON-STD

Is the

video input signal a composite

signal?

YES

NO

What is

the setup menu No. 303

(STD/NON-STD)

setting?

AUTO

NON-STD

Is the

video input signal a standard

or non-standard signal?

STD

STD

YES

«
...
63
64
65
66
67
...
»

Summary of Contents for AJ-SD965p























































































Reviews:

No comments

Related manuals for AJ-SD965p

Brand: Telycam Pages: 28

Digital Video Camera GR-DX78

Brand: JVC Pages: 52

Digital Video Camera GR-D34

Brand: JVC Pages: 40

Brand: JVC Pages: 16

Enverio GZ-MS210 PEK

Brand: JVC Pages: 24

Brand: JVC Pages: 44

CU-VD3 - Everio Share Station

Brand: JVC Pages: 52

Digital Movie Camera with Hard Drive

Brand: JVC Pages: 3

CYBERCAM GR-DVF31

Brand: JVC Pages: 64

EVERIO GZ-HM440U

Brand: JVC Pages: 64

DZ-VCA3U - 3-ccd Micro Hdtv Camera

Brand: JVC Pages: 24

DZ-VCA3U - 3-ccd Micro Hdtv Camera

Brand: JVC Pages: 2

Digital Media Camera LYT1366-001B

Brand: JVC Pages: 80

DX97US - GRDX97 MiniDV Digital Camcorder

Brand: JVC Pages: 52

Everio 1109MNH-SW-VMUC

Brand: JVC Pages: 64

Brand: JVC Pages: 28

Brand: JVC Pages: 8

Digital Video Camera GR-D24

Brand: JVC Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands