11
General
：
Features of the Input/Output unit
Ge
ner
a
l
(Reference values when cards are used for continuous
recording with our products. Actual recording time depends
on the kind of scenes and the number of clips.)
The driver installed on the unit must be updated when
using SD memory cards other than as listed above. To
update the driver, refer to [Updating the firmware
incorporated into the camera-recorder] (page 193)
For the latest information on P2 cards and SD memory
cards not available in the operating Instructions, visit the
P2 Support Desk at the following Web sites.
https://eww.pavc.panasonic.co.jp/pro-av/
_
Features USB2.0 port (HOST/DEVICE)
By connecting with a PC via USB2.0, a P2 card inserted
in AJ-HPX3000 can be used as a bulk storage device.
It is also possible to store data on a P2 card onto a USB
2.0-connected external hard disk equipped with USB
host capability as well as view clips stored on hard disks
and write them to P2 cards. (Refer to page 135)
_
DVCPRO (IEEE1394) input/output provided as a
standard configuration
Data can be input/output to an external device through
the IEEE1394 digital interface. Use a 6-pin type
connector. The unit does not support the bus power.
While operating AVC-Intra, it is impossible to input/
output data with IEEE 1394. (Refer to page 133)
_
HD/SD SDI output featured as standard
Video can be output as HD SDI signals, down-converted
SD SDI signals, or analog composite signals. SDI output
includes embedded audio etc.. (Refer to page 44) Note
that the SD mode does not output HD SDI signals.
_
Down converter output provided as a standard
configuration
In HD mode, the MON OUT output connector and the
VIDEO OUT connector (in setting VBS mode) output
down converter (analog composite) signals.
It is optimum for confirming shot images on the SD
monitor. (Refer to page 44)
_
HD/SD SDI input function (when the AJ-
YA350AG is attached)
The camera-recorder with the AJ-YA350AG extension
board attached can record SDI signals input through the
SDI input connector only if the signals are in the same
format as the camera-recorder.
(The unit does not support the various Native methods.)
_
Remote control connector
By connecting the remote control unit (AJ-RC10G),
which is available as an optional accessory, the unit can
be controlled remotely. (Refer to page 111)
_
Confirmation of return video signals
It is possible to confirm the return video signals (analog
HD-Y signals in the HD mode/VBS or Y signals in the
SD mode) supplied to the GENLOCK IN connector of
AJ-HPX3000 in the viewfinder to confirm programs.
(Only video signals from the same record format can be
confirmed.) (Refer to page 178)
_
DC OUT connector
The DC OUT connector of the unit produces 1.5 A of
electrical current.
By connecting an external switch to this connector, it is
possible to control REC start/stop.
Since a tally lamp can be used by connecting the LED
to this connector, it is useful for shooting video when
fixing the camera on a crane. (Refer to page 112)
Approximate Proxy Recording Time (optional) on SD memory cards
(Except for 24P native mode)
Card No.
(Card Capacity)
MPEG4 recording rate
192 kbps
768 kbps
1500 kbps
RP-SDH256
(256 MB)
Approx.
2 hour
17 minutes
Approx. 35
minutes
Approx. 19
minutes
RP-SDH512
RP-SDK512
(512 MB)
Approx.
4 hour
27 minutes
Approx. 69
minutes
Approx. 38
minutes
RP-SDQ01G
RP-SDK01G
(1 GB)
Approx.
8 hour
56 minutes
Approx.
2 hour
19 minutes
Approx. 77
minutes
RP-SDQ02G
RP-SDK02G
(2 GB)
Approx.
18 hour
11 minutes
Approx.
4 hour
44 minutes
Approx.
2 hour
37 minutes
RP-SDV024G
(SDHC 4 GB)
Approx.
35 hour
42 minutes
Approx.
9 hour
18 minutes
Approx.
5 hour
12 minutes
Features of the Input/Output unit
AJ-HPX3000G(VQT1D27)E.book 11 ページ ２００７年９月３日 月曜日 午後２時３４分
