manualshive.com logo in svg

Panasonic AFP7CPS31, User Manual

Share
Download
Panasonic AFP7CPS31 User Manual Download Page 93

8.1

 

CPU Unit Specifications

 

8-17

 

 

8.1.6  List of System Data Registers 

SD0 – SD39 

Device 

number 

Name 

Description 

SD0 

Self-diagnostic error code 

Stores the error code when a self-diagnosis error occurred. 

SD1 

Alarm Occurrence Unit Slot No. 

Saves the slot number of the unit where an alarm has 
occurred. 

SD2 

Error Occurrence Unit Slot No. 

Saves the slot number of the unit where an error has 
occurred. 

SD3 

Warning Occurrence Unit Slot No. 

Saves the slot number of the unit where a warning has 
occurred. 

SD4 

Verification Error Occurrence Unit 
Slot No. 

Saves the slot number of the unit where a verification error 
has occurred. 

SD5 

Installation error detection slot No. 

Saves the slot number of the unit where an installation error 
was detected. 

SD6 (Not 

used) 

 

SD7 

Operation error occurrence PB 
number (hold type) 

Saves the PB number where the first operation error occurred 
after the unit has started operating. 

SD8 

Operation error occurrence 
address (hold type)  
 (32-bit lower-level address)  

SD9 

Operation error occurrence 
address (hold type)  
 (32-bit higher-level address)  

Saves the address where the first operation error occurred 
after the unit has started operating. Perform monitoring using 
32-bit data. 

SD10 

Operation error occurrence PB 
number (latest type) 

Saves the PB number where an operation error occurred. 
Every time a new error occurs, the data are updated. The 
value '0' is recorded at the start of the scan. 

SD11 

Operation error occurrence 
address (latest type)  
 (32-bit lower-level address)  

SD12 

Operation error occurrence 
address (latest type)  
 (32-bit higher-level address)  

Saves the address where an operation error occurred. Every 
time a new error occurs, the data are updated. The value '0' is 
recorded at the start of the scan. Perform monitoring using 32-
bit data. 

SD13 
 to SD18 

(Not used) 

 

SD19 

RING counter 2.5 ms  

SD20 

RING counter 10 

μ

s  

SD21 

RING counter 100 

μ

s  

The saved value is increased by one every time the respective 
time unit has passed. (H0 to HFFFF) 
Current values of SD19 to SD21 can only be read when SD19 
to SD21 are directly specified and read by MV instruction. The 
scan start value is read by other instructions. 

SD22 

Scan time (current value) 

Saves the current 
value. 

SD23 

Scan time (minimum value) 

Stores the minimum 
value. 

SD24 

Scan time (maximum value) 

Saves the maximum 
value. 

[Saved value (decimal)] x 10 

μ

s 

scan time indication: Indicates 
operation cycle time in the RUN 
mode only. Max. and Min. values 
are cleared at switching between 
the RUN mode and the PROG. 
mode. 

SD25 
 to SD26 

(Not used) 

 

SD27 

Interval for PB for execution at a 
specified interval 

Saves interval for PB for execution at a specified interval. 

SD28 
 to SD29 

(Not used) 

 

SD30 

SD card access instruction 
execution result 

Error codes while the SD card access instruction is executed 
are stored. 

SD31 
 to SD39 

(Not used) 

 

(Note 1): SD0 to SD5 are available only when the corresponding system relays SR0 to SR5 are on. 

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for AFP7CPS31














































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands