manualshive.com logo in svg

Panasonic AFP7CPS31, User Manual

Share
Download
Panasonic AFP7CPS31 User Manual Download Page 52

 

5-6 

Operation

 

 

5.2.3  Data Hold During Power Failure 

The FP7 CPU unit backs up most data into ROM (non-volatile memory). 

 

Data saved in ROM (non-volatile memory) 

• Project data (programs, configuration data, comments) 

• Hold type data in the operation memory 

• System monitors, system records data (e.g. lifetime data, error records) 

 

Data held by the built-in capacitor and the backup battery 

• Calendar timer 

KEY POINTS

 

 

Calendar timer values can continue operation for about one week by the 
built-in capacitor, even if no battery is used. 

 

In order to charge the built-in capacitor, supply power to the CPU unit for at 
least 30 minutes. 

5.2.4  Online Editing 

The FP7 CPU unit can be edited online. Usable operations vary by mode. 

 

PROG. mode 

• While editing a program, the program inside the RAM is rewritten by PG converting a given 
network inside the program block that is being edited. 

• Rewritten data in the RAM is incorporated into the ROM1. 

• Comments and configuration data can also be rewritten.  

 

RUN mode 

• While editing a program, the program is written into the RAM by PG converting a given 
network inside the program block that is being edited. 

• Rewritten data in the RAM is incorporated into the ROM1. 

• Configuration data cannot be rewritten. 

• Comments can be rewritten. 

• It is not possible to download the entire project. 

• It is possible to download the Program Block (PB). 

After a program is rewritten in the RUN mode, operation stops for a time length proportionate 
to the size of the relevant PB. 

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for AFP7CPS31














































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands