manualshive.com logo in svg

Panasonic AFP7CPS31, User Manual

Share
Download
Panasonic AFP7CPS31 User Manual Download Page 7

Table of Contents 

iii

 

 

5.1.1

 

Check Points ...........................................................................................5-2

 

5.1.2

 

Procedures before Starting Operation ....................................................5-3

 

5.2

 

RAM/ROM Operation.............................................................................. 5-4

 

5.2.1

 

Transmission of the Project.....................................................................5-4

 

5.2.2

 

Operations following Powering On..........................................................5-5

 

5.2.3

 

Data Hold During Power Failure .............................................................5-6

 

5.2.4

 

Online Editing ..........................................................................................5-6

 

5.3

 

Backing Up the Project ........................................................................... 5-7

 

5.3.1

 

Transmission from the Execution Memory RAM to the Backup Memory 
ROM2 ......................................................................................................5-7

 

5.3.2

 

Transmission from the Backup Memory ROM2 to the Execution Memory 
RAM/ROM1 .............................................................................................5-8

 

5.3.3

 

Operations following Powering On/Off ....................................................5-8

 

5.4

 

SD Memory Card Operation ................................................................... 5-9

 

5.4.1

 

Preparing SD Memory Cards ..................................................................5-9

 

5.4.2

 

How to Insert an SD Memory Card .......................................................5-10

 

5.4.3

 

Saving an Execution File for SD Memory Card Operation ...................5-11

 

5.4.4

 

Provisional Operation by an SD Memory Card .....................................5-12

 

5.4.5

 

Transmission from an SD Memory Card to the Execution Memory......5-14

 

5.4.6

 

Precautions Concerning SD Memory Card Operation ..........................5-15

 

6. 

 

Troubleshooting ..................................................................6-1

 

6.1

 

Self-Diagnosis Function.......................................................................... 6-2

 

6.1.1

 

CPU Unit's Operation Monitor LED.........................................................6-2

 

6.1.2

 

Operation at the Time of Error ................................................................6-2

 

6.2

 

What to Do If an Error Occurs ................................................................ 6-3

 

6.2.1

 

ERROR LED Flashes on the CPU Unit ..................................................6-3

 

6.2.2

 

PROG Mode Does Not Change to RUN .................................................6-4

 

6.2.3

 

ALARM LED Turns ON on the CPU Unit ................................................6-4

 

6.2.4

 

POWER LED Does Not Turn ON on the Power Supply Unit..................6-5

 

6.2.5

 

A Protect Error Message Appears ..........................................................6-5

 

6.2.6

 

If Expected Output Is Not Available ........................................................6-6

 

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for AFP7CPS31














































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands