Panasonic AFP7CPS31 User Manual Download Page 13

Page: 13 / 109

1.2

Restrictions on Combinations of Units

1-5

1.2.4 Restrictions on Communication Functions to be Used

There are the following restrictions on functions to be used when using the SCU or ET-LAN
that is built in the CPU unit, or the serial communication unit (SCU).

Function to be used

Restrictions

PLC link function

Up to two communication ports can be used. For using two ports, allocate
different link areas to them.

SCU built-in the CPU unit (COM.1 port)

Serial communication unit (COM.1 port)

MEWTOCOL-COM master

MODBUS-RTU master

A maximum of 16 communication ports and the number of connections in
combination can be used simultaneously.

SCU built-in the CPU unit (COM.1 port to COM. 2 port)

Serial communication unit (COM.1 port to COM.4 port)

ET-LAN built-in the CPU unit (User connections 1 to 16)

MEWTOCOL-COM slave

MEWTOCOL7-COM slave

MODBUS-RTU slave

A maximum of 15 communication ports and the number of connections in
combination can be used simultaneously.

SCU built-in the CPU unit (COM.1 port to COM. 2 port)

Serial communication unit (COM.1 port to COM.4 port)

ET-LAN built-in the CPU unit

(System connections 1 to 4 / User connections 1 to 16)

General-purpose
communication

There is no restriction.

1.2.5 Unit to be Used and Applicable Versions of CPU Unit and FPWIN GR7

For using the unit, the following versions of CPU unit and FPWINGR7 are required.

Applicable versions

Unit type

CPU unit

FPWINGR7

Remarks

FP7 High-speed Counter Unit

Ver.1.2 or later

(Note 1)

FP7 Serial Communication Unit

Ver.1.2 or later

Ver.1.3 or later

FP7 Communication Cassette
(Ethernet type)

Ver.1.3 or later

Ver.1.0 or later

(Note 2)

FP7 Analog I/O Cassette, Analog
Input Cassette, Thermocouple Input
Cassette

Ver.2.0 or later

FP7 Pulse Output Unit

Ver.2.0 or later

(Note 1) For using the high-speed counter unit and the positioning unit in combination, and for using the interrupt

function with the high-speed counter unit, the positioning unit Ver.1.1 or later is required.

(Note 2) Configurator WD should be Ver.1.7 or later.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for AFP7CPS31














































































































Search results

Summary of Contents for AFP7CPS31

Reviews:

Brands by name

Popular brands

Panasonic AFP7CPS31, User Manual

Search results

Summary of Contents for AFP7CPS31

Reviews:

Brands by name

Popular brands