Panasonic AFP7CPS31 User Manual Download Page 34

Page: 34 / 109

4-2

Installation

and Wiring

4.1 Installation

4.1.1 Installation Environment and Space



Installation environment

Operating environment (Use the unit within the range of the general specifications when
installing)



Ambient temperatures: 0 to +55





Ambient humidity: 10 to 95%RH (at 25



C, no-condensing)



Pollution degree 2



Usable altitude: 2,000m above sea level or lower



Equipment class: Class 1



Overvoltage category: II or lower



Installation location: Inside the control panel

Do not use the unit in the following environments.

- Direct sunlight

- Sudden temperature changes causing condensation

- Inflammable or corrosive gas

- Excessive airborne dust, metal particles or saline matter

- Benzine, paint thinner, alcohol or other organic solvents or strong alkaline solutions such as
ammonia or caustic soda

- Direct vibration, shock or direct drop of water.

- Influence from power transmission lines, high voltage equipment, power cables, power
equipment, radio transmitters, or any other equipment that would generate high switching
surges (100 mm or more)



Clearance



In order to secure clearance for ventilation, ensure that the top and the bottom of the unit are

at least 50 mm away from other devices, wiring ducts, etc.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for AFP7CPS31














































































































Search results

Summary of Contents for AFP7CPS31

Reviews:

Brands by name

Popular brands

Panasonic AFP7CPS31, User Manual

Search results

Summary of Contents for AFP7CPS31

Reviews:

Brands by name

Popular brands