background image

2

BENTO 32 CORTEN FIRE PIT Electronic Ignition | Installation & Owner's Manual

SAFETY INFORMATION

 WARNINGS:

IMPORTANT: This appliance should 

be inspected before use and at least 

once annually by a qualified service 

person.

More frequent cleaning may be 

required as necessary. It is imperative 

that the control compartment, 

burners and circulating air 

passageways of the appliance be 

kept clean.

DANGER: Carbon monoxide 

poisoning can lead to death!

CARBON MONOXIDE POISONING:

Early signs of carbon monoxide 

poisoning resemble the flu, with 

symptoms including headache, dizziness, 

or nausea. If you experience these 

signs, the Fire Pit may not be working 

properly. Get fresh air at once! Have the 

Fire Pit serviced. Some people are more 

affected by carbon monoxide than others, 

including pregnant women, people with 

heart or lung disease or anemia, those 

under the influence of alcohol, and those 

at high altitudes.

NATURAL GAS AND PROPANE: 

To assist in detecting leaks, an odorant 

has been added to natural gas and 

propane. However, this odorant can fade, 

and gas may be present even though no 

odor exists. Make certain you read and 

understand all warnings. Keep this manual 

for reference. It is your guide to safe and 

proper operation of this appliance.

WARNING:

 Any modification to this appliance or its 

controls can be dangerous.

1.  This appliance, as supplied, is only for use with the 

type of gas indicated on the rating plate.

2.  When this appliance is connected to a fixed piping 

system, the installation must conform to local codes, 

or in the absence of local codes, to the National 

Fuel Gas Code, ANSI Z223.1/NFPA 54, or the 

International Fuel Gas Code.

3.  Keep the appliance area clear and free from 

combustible materials, gasoline and other flammable 

vapors and liquids

4.  Do not burn solid fuel in this appliance. Do not use 

this appliance to cook food or to burn paper or other 

objects.

5.  Children and adults should be alerted to the hazards 

of high surface temperatures and should stay away 

to avoid burns or clothing ignition.

6.  Clothing or other flammable materials should not be 

hung from the appliance, or placed on or near the 

appliance.

7.  Young children should be carefully supervised when 

they are in the area of the appliance.

8.  Do not use the appliance if any part has been under 

water. Immediately call a qualified service technician 

to inspect the appliance and to replace any part of 

the control system and any gas control which has 

been under water.

9.  Inspect the appliance before each use.

10. Turn the appliance off and let cool before servicing, 

installing, repairing or covering. Any guard or other 

protective device removed for servicing the appliance 

must be replaced prior to operating the appliance. 

Only a qualified service person should install, service, 

or repair the appliance.

HIGH ALTITUDE INSTALLATION

The appliance is certified for installations up to 4500’ 

(1372 m) above sea level. At this altitude range, no 

changes to the appliance are required. Please contact 

Paloform for information regarding installation above 

4500’ (1372 m).

LOCAL CODES

The installation of this appliance must conform with local 

codes, or in the absence of local codes, with the National 

Fuel Gas Code, ANSI Z223.1 • NFPA 54; National Fuel 

Gas Code; Natural Gas and Propane Installation Code, 

CSA B149.1; or Propane Storage and Handling Code, 

CSA B149.2, as applicable.

Summary of Contents for BENTO 32 CIR-E-18


















Reviews: