Pall PadMixer 1000 Premium Instructions For Use Manual Download Page 47

Page: 47 / 48

020-17467-00 Instructions For Use PadMixer 1000 Premium RevD

7 General machine specifications

7.1 Materials

Plate material (outside plate surfaces)

Stainless steel 316L
Brushed surface finish
Surface roughness <1.2 µm Ra / 47 µin Ra

Frame material (inside frame, mixing head
bottom plate and handlebar)

Stainless steel 316L
Bead blasted surface finish
Surface roughness <2 µm Ra / 79 µin Ra

Wheels (castors)

White polyamide

Protection guide and blocks

PTFE

Certain components in the mixing head

PEEK

7.2 Capacity

The machine is designed to work with PadMixer mixing biocontainers of 25, 50, 200, 500 and
1000L.

The minimum mixing speed is set at 30 RPM, the maximum speed is 150 RPM.

7.3 Noise level

The machine generates a noise level of less than 75 dB.

7.4 Operating temperature

The ambient operating temperature is 0°C to 50°C. For more details, consult the equipment
specification.

8 Service

The mixing tank was developed exclusively for mixing fluids, and solids in fluids, in specially
designed disposable mixing biocontainers. The tank should only be used for this purpose to
ensure a long service life.

Should your system require service, please contact your local sales team.

For information about applicable patents, visit

www.pall.com/patents

*BarbLock® is a registered trademark of Saint-Gobain Corporation.

(Pall logo), Pall and PadMixer are trademarks of Pall Corporation.

® indicates a trademark registered in the USA. © Pall Corporation 2015.

Summary of Contents for PadMixer 1000 Premium

















































Search results

Summary of Contents for PadMixer 1000 Premium

Reviews:

Related manuals for PadMixer 1000 Premium

Brands by name

Popular brands

Pall PadMixer 1000 Premium, Instructions For Use Manual

Search results

Summary of Contents for PadMixer 1000 Premium

Reviews:

Related manuals for PadMixer 1000 Premium

Brands by name

Popular brands