Pall PadMixer 1000 Premium Instructions For Use Manual Download Page 41 | Manualshive

Page: 41 / 48

background image

020-17467-00 Instructions For Use PadMixer 1000 Premium RevD

41

Now there is free access to the gearbox. Disconnect the power supply cable, remove the
RPM counter disc and the bracket with the 2 sensors. Disconnect the mixing head from the
motor axes and remove the motor from the support plate by means of the 4 screws.

The recommend oil type ISO VG 220.

6.7 Uploading a new PLC code

This chapter explains how a new or modified PLC code can be uploaded onto the systems
PLC.

When a new code is uploaded, some old information that is stored in the program will be lost.
Therefore note all Recipe settings and Factory settings so that these can be edited when the
new code is installed.

Load the new or modified PLC code on a CF-card (Compact Flash).

2 files + 1 folder should be loaded onto the CF-card, so not under another directory or folder.
The following type of files and folder should be saved on the CF-card :

Figure 47: Overview of files and folders to be saved on the CF card

Turn off the main power the mixing system.

Open the back of the touch screen box (4 screws). Open the CF-card slot and insert the CF-
card.

Figure 48: Inserting the CF card

«
...
39
40
41
42
43
...
»

Summary of Contents for PadMixer 1000 Premium

















































Reviews:

No comments

Related manuals for PadMixer 1000 Premium

Brand: Rath Pages: 3

Brand: FJC Pages: 2

Brand: Vahle Pages: 96

Brand: KaVo Pages: 49

Brand: Easson Pages: 33

Brand: Jacto Pages: 12

Saturn 2000 GC/MS

Brand: Varian Pages: 9

Brand: Xaoc Devices Pages: 8

Brand: KCI Pages: 2

Brand: KCI Pages: 60

Brand: Landoll Pages: 38

Brand: Additel Pages: 107

Brand: Magicfx Pages: 25

Brand: Valmont Structures Pages: 8

Brand: Gilson Pages: 8

Zen-O lite RS-00600

Brand: GCE Pages: 20

Brand: PHAROS MARINE Pages: 17

Haymakers Hooimakers F80-350V

Brand: Falcon Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands