oxycom 3800OXYSTD Manual Download

Page: 63 / 68

Operation procedures

Version 1.3, 2021-12-14

S15: Max Fan Free

Cooling

Setting

Maximum fan speed for free-cooling

S16: Min Fan Cooling

Setting

Minimum fan speed for cooling

S17: Max Fan Cooling

Setting

Maximum fan speed for cooling

S18: Cooling release

Setting

°C

Minimum outdoor temperature for

cooling. At a cooling demand below this

temperature, the system will switch to

free-cooling.

S19: Thermostat ID

Setting

Thermostat Modbus ID (corresponding

thermostat).

S20: Control

Setting

Thermostat

Control type.

S21: Modbus Address

Setting

Unit modbus ID.

S22: Modbus Baudrate

Setting

19200

Unit modbus baudrate.

S23: Modbus Parity

Setting

8N1

Unit modbus parity.

S24: Drain Valve

Setting

2-wire N.O.

Configure drain valve type (older units

have 3-wire valves, new units have 2-wire

valve).

S25: Water Desinfection

Setting

None

UV-C Lamp on / off. (Optional)

S26: Digital Input J12

Setting

Not used

Select function of digital input J12: Not

used / AHU pre-cooling / Fire contact.

S27: Winter Model

Setting

Off

Enable / disable winter mode - winter

mode enables free-cooling instead of

cooling.

S28: Model

Setting

Set model type.

S29: Serialnumber

Setting

Set serial number.

S30: Language

Setting

English

Set display menu language.

S31: Factory Setting

Setting

Load factory settings (saving settings

required to activate).

5.2.6

Error codes on OxyLogic LCD

Reset error: Press the reset button [3] located directly below the OxyLogic LCD
(left side).

Summary of Contents for 3800OXYSTD





































































Search results

Summary of Contents for 3800OXYSTD

Reviews:

Related manuals for 3800OXYSTD

Brands by name

Popular brands

oxycom 3800OXYSTD, Manual

Search results

Summary of Contents for 3800OXYSTD

Reviews:

Related manuals for 3800OXYSTD

Brands by name

Popular brands