manualshive.com logo in svg

oxycom 3800OXYSTD, Manual

Share
Download
oxycom 3800OXYSTD Manual Download Page 53

Version 1.3, 2021-12-14

53

1

2

3

4

5

5

Operation procedures

5.1

How to operate the IntrCooll®

5.1.1

Checks before starting

Before starting make sure that:
-

All panels and covers of the IntrCooll® are installed.

-

There is no marking on the IntrCooll® ‘DO NOT START’.

-

There are no loose or strange parts within the IntrCooll®.

-

The water supply to the IntrCooll® is connected.

-

The correct filters are installed.

-

The correct flow regulator cap (50 Hz / 60 Hz) is installed.

-

The drain is connected to a local drain circuit

-

The IntrCooll® is connected to the mains power supply.

-

The maintenance switch is in ON position.

-

The padlock switch is in ON postion.

-

The thermostat is switched on and connected to the IntrCooll®.

-

For correct settings, refer to the enclosed documentation in the thermostat
package.

5.1.2

Check unit installation

Check and finish filling in the Installation checklist on page 48.

Summary of Contents for 3800OXYSTD





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands