OWL Fiber OWL 7+ Operation Manual Download Page 22

Page: 22 / 89

The Fiber OWL 7+ and WaveSource Pro are now ready to take measurements.

TEST PROCEDURES

Measure the attenuation, or loss, of optical fiber links.

Connect the meter and source into the each fiber in the link under test as shown.
The meter will begin to display loss readings automatically after a few seconds.

OPM MODE

– start testing

YES

Optical Source

WaveSource Pro

AUTO

PORT

MOD

SIDE A

SIDE B

Do you wish to start testing

this fiber link now?

YES

Avoid disconnecting the

reference cable from the light
source port.

If the reference cable was
detached for any reason,
re-set the reference.

Optical Source

WaveSource Pro

AUTO

PORT

MOD

WAVE

OPM

WAVE:

1310

ENTER

-1.72

1310nm REL

Ref: -10.25dBm

-1.33

1550nm REL

Ref: -10.26dBm

OPTICAL LOSS MEASUREMENT, cont.

Summary of Contents for Fiber OWL 7+


























































































Search results

Summary of Contents for Fiber OWL 7+

Reviews:

Related manuals for Fiber OWL 7+

Brands by name

Popular brands

OWL Fiber OWL 7+, Operation Manual

Search results

Summary of Contents for Fiber OWL 7+

Reviews:

Related manuals for Fiber OWL 7+

Brands by name

Popular brands