OWL Fiber OWL 7+ Operation Manual Download Page 21

Page: 21 / 89

TEST PROCEDURES

OPTICAL LOSS MEASUREMENT, cont.

OPM MODE

Store the reference values.

– store the

reference value and
continue.

DONE

Optical Source

WaveSource Pro

AUTO

PORT

MOD

Wavelength

1310nm

1550nm

Set source to AUTO or 1310nm

You will need to set a source
power reference for each
wavelength that you are testing.

Press TEST to measure.
Press DONE after testing all
wavelengths.

TEST

WAVE

BACK

DONE

SOURCE REFERENCE POWER

HELP

Power

-10.21dBm

-10.60dBm

Typical

-10.00dBm

The source is now set
to AUTO mode.

– acquire

reference values
from the source

TEST

Optical Source

WaveSource Pro

AUTO

PORT

MOD

Wavelength

Set source to AUTO or 1310nm

You will need to set a source
power reference for each
wavelength that you are testing.

Press TEST to measure.
Press DONE after testing all
wavelengths.

Power

Typical

TEST

WAVE

BACK

DONE

SOURCE REFERENCE POWER

HELP

– Power ON the

WaveSource Pro.

– change port

(if necessary)

Hold – set the
WaveSource Pro
to AUTO mode

PORT

AUTO

Set up the WaveSource Pro.

Summary of Contents for Fiber OWL 7+


























































































Search results

Summary of Contents for Fiber OWL 7+

Reviews:

Related manuals for Fiber OWL 7+

Brands by name

Popular brands

OWL Fiber OWL 7+, Operation Manual

Search results

Summary of Contents for Fiber OWL 7+

Reviews:

Related manuals for Fiber OWL 7+

Brands by name

Popular brands