OWL Fiber OWL 7+ Operation Manual Download Page 57

Page: 57 / 89

ENTER THE LINK LENGTH

TEST PROCEDURES

CERT MODE

On the meter, press

. Enter the length in meters using the keypad that appears,

then press

LENGTH

DONE

Optical Source

WaveSource Pro

AUTO

PORT

MOD

Enter fiber length in meters:

ABCDEFGHIJKLM
NOPQRSTUVWXYZ
0123456789 : ; <

<--

SHIFT

SPACE

DONE

Use arrows to highlight letter
then press the enter key. Tap
the power button to abort.

100

NOTE: to convert feet to meters,
use the conversion factor of
3.28 feet per meter.

The link budget will be adjusted (based on the cabling standard) to accommodate the fiber length.

Optical Source

WaveSource Pro

AUTO

PORT

MOD

CERT

FIBER#1

ACME CORP / HQ WEST
M=COMPUTER ROOM I=NETWORK HUB 3

Length:

0m WAVE:

EIA/TIA 568C.3 CON: 2
INDOOR SM SPL: 2

100

1310

ENTER

-0.00

1310nm REL

PASS

2.50

-0.00

1550nm REL

PASS

2.50

TEST

SAVE

LENGTH

WAVE

Summary of Contents for Fiber OWL 7+


























































































Search results

Summary of Contents for Fiber OWL 7+

Reviews:

Related manuals for Fiber OWL 7+

Brands by name

Popular brands

OWL Fiber OWL 7+, Operation Manual

Search results

Summary of Contents for Fiber OWL 7+

Reviews:

Related manuals for Fiber OWL 7+

Brands by name

Popular brands