OWL Fiber OWL 7+ Operation Manual Download Page 17 | Manualshive

Page: 17 / 89

background image

TEST PROCEDURES

RECEIVER SENSITIVITY MEASUREMENT

Output power measured from a transmitter through a link at the far-end receiver will determine if the
received power is within manufacturer receiver sensitivity specifications.

OPM MODE

Remove the patch cable from the
receiver (RX) port.

TX RX

TX RX

Connect the patch cable to the OPM port on the
Fiber OWL 7+. Set the meter to dBm mode, and
also the same wavelength as the transmitter.

TX RX

TX RX

WAVE

OPM

WAVE:

1310

ENTER

LOW

1310nm ABS

dBm

View displayed receiver sensitivity power level.

NOTE: if the transmitter is sending out digital data, the displayed power
level will fluctuate based on average power of data bits received during
the sampling period.

TX RX

TX RX

WAVE

OPM

WAVE:

1310

ENTER

-14.72

1310nm ABS

dBm

«
...
15
16
17
18
19
...
»

Summary of Contents for Fiber OWL 7+


























































































Reviews:

No comments

Related manuals for Fiber OWL 7+

Brand: Bante Instruments Pages: 6

Brand: IFR Pages: 46

Brand: Saimo Pages: 101

Brand: Vaisala Pages: 90

Brand: Vaisala Pages: 4

Brand: Yamaha Pages: 17

Brand: Yamaha Pages: 23

Brand: Yamaha Pages: 16

Brand: Yamaha Pages: 28

Brand: Yamaha Pages: 19

Brand: Yamaha Pages: 57

Clavinova CVP-204

Brand: Yamaha Pages: 56

disklavier Mark III Series

Brand: Yamaha Pages: 50

Brand: Yamaha Pages: 23

BML-S1G0-Q71 Series

Brand: Balluff Pages: 20

Brand: Dynojet Pages: 88

Brand: VP instruments Pages: 15

Brand: DODODUCK Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands